US Robotics Courier USR3510 Скачать руководство пользователя страница 112

Страница: 112 / 162

Revision: 1.00

112 |

P a g e

If everything is accepted by the validation, a confirmation box will appear that an email has been
sent and you need to open your email account to validate your email address.

Click the email link and your browser will open and direct you to USR Universe.

You are now signed in and can start to use USR Universe!

Signing In

To Sign in to USR Universe:

In a web browser, enter the URL:

http://www.usr.com/activate/3510

Enter your email and password and click the 'Blue' button...Sign in >



Click

Forgot your password?

and follow the instructions to reset your password.



Click

Sign up now!

create an account

Содержание Courier USR3510





























































































































































Результаты поиска

Содержание Courier USR3510

Отзывы:

Похожие инструкции для Courier USR3510

Бренды по названию

Популярные бренды

US Robotics Courier USR3510, Руководство пользователя

Результаты поиска

Содержание Courier USR3510

Отзывы:

Похожие инструкции для Courier USR3510

Бренды по названию

Популярные бренды