US Robotics Courier USR3510 Скачать руководство пользователя страница 110

Страница: 110 / 162

Revision: 1.00

110 |

P a g e

USR Universe Guide

The USR Universe Guide explains how to deploy firmware, configuration, and developer images to
multiple devices.

This guide is designed for:



Distributors



System integrators



Developers



Field engineers

Information about installing and configuring the Gateway is available in the

User Guide

section of this

document. Details about Gateway hardware specifications and technical information are available in the

Hardware Guide

section of this document.

And this Gateway design can be licensed to third party hardware and software developers who want to
create custom expansion cards and software images for specific needs. For information on the
developer program, contact USRobotics Customer Support.

Introducing the USR Universe

The USR Universe is the configuration and deployment mechanism for the Gateway. From the factory,
the Gateway base units have no customization.

power-up

, the Gateway connects to the USR Universe over the wired Ethernet port and

automatically downloads the appropriate update. If the Ethernet interface is unavailable, then the
Gateway uses the

WWAN interface

to download the updates.

The Gateway can download the following files from the USR Universe:



Gateway firmware: System firmware provided by USRobotics.



Gateway radio firmware image: software that updates changes to wireless operator firmware



Gateway config file: configuration settings that can be applied to one or more Gateways



Gateway application: customized software that provides additional functionality to the device or
controls third-party expansion cards.

Creating an Account

The following steps are needed for creating an account:

Tip:

You can set the USR Universe to enable or disable the automatic downloads.

Содержание Courier USR3510





























































































































































Результаты поиска

Содержание Courier USR3510

Отзывы:

Похожие инструкции для Courier USR3510

Бренды по названию

Популярные бренды

US Robotics Courier USR3510, Руководство пользователя

Результаты поиска

Содержание Courier USR3510

Отзывы:

Похожие инструкции для Courier USR3510

Бренды по названию

Популярные бренды