US Robotics Courier USR3510 Скачать руководство пользователя страница 23

Страница: 23 / 162

Revision: 1.00

23 |

P a g e

LAN interfaces



Displays a list of the available LAN interfaces and their IP addresses.

VPN Tunnels

Displays a list of the active VPN tunnels.

System information

Device serial number



Displays the serial number of the gateway

Firmware version



Displays the current version of the system firmware. System firmware is required for the
gateway to operate.

Image version



Displays the version of the developers image. This image is only required in case you need
features which are not part of the system firmware.

Configuration version



Displays the version of the configuration file.



A configuration file is not mandatory, it's a way to provision gateway settings to multiple units.

IMPORTANT:

The gateway decides that it's not connected anymore when:

- the Ethernet connection cable is removed.
-  when a disconnect message of the network is received via the 3G connection
-  when the WLAN connection is out of range.

This functionality can be extended when used together with the

connection persistence

feature.

Содержание Courier USR3510





























































































































































Результаты поиска

Содержание Courier USR3510

Отзывы:

US Robotics Courier USR3510, Руководство пользователя, Страница: 23 / 162

Результаты поиска

Содержание Courier USR3510

Отзывы: