US Robotics Courier USR3510 Скачать руководство пользователя страница 47

Страница: 47 / 162

Revision: 1.00

47 |

P a g e

Settings

Enable Automatic Provisioning



Controls automatic updates from the USR Universe.



Set to

Yes

to automatically check for updates. This happens:

Each time the unit is powered on.

Depending on the "check-in frequency" parameter on the USR Universe.



Set to

to disable automatic provisioning.

System Tab

The System tab configures remote access settings, log file parameters, and manual reset settings.

It includes the following sections:



Time Settings



Power Savings



Data counters



Remote Access



Dynamic DNS



Username and Password



Logging



Config Export



System Reboot and Factory Reset

Содержание Courier USR3510





























































































































































Результаты поиска

Содержание Courier USR3510

Отзывы:

Похожие инструкции для Courier USR3510

Бренды по названию

Популярные бренды

US Robotics Courier USR3510, Руководство пользователя

Результаты поиска

Содержание Courier USR3510

Отзывы:

Похожие инструкции для Courier USR3510

Бренды по названию

Популярные бренды