US Robotics Courier USR3510 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 162

background image

Revision: 1.00

Copyright 2015 U.S. Robotics Corporation

18 |

P a g e

Related Topics

Configuring Expansion Cards

Mounting the Gateway

The gateway can be mounted on a wall or DIN rail.

Mounting on a wall

The gateway can be mounted on a wall with six screws. The mounting holes in the base of the gateway
have a diameter of 4.3 mm. USRobotics recommends using screws with a minimum width of 4mm and a
minimum length of 30 mm (M4x30mm).

To wall mount the gateway:

1.

Mark the six holes with a pencil on the wall.

2.

Drill (if necessary) the holes in the mounting surface. Do not drill into the gateway housing.

Click

here for a drawing of the mounting holes.

3.

Mount the gateway with six M4x30mm screws

Tip:

When choosing the mounting orientation of the unit, consider the direction of the cables and

antennas. Make sure cables are routed with sufficient ease to all connectors, and that the antennas
are unobstructed for easy positioning. The front panel LEDs should also be visible.

IMPORTANT:

All mounting hardware is installer provided.

«
...
16
17
18
19
20
...
»

Содержание Courier USR3510



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Courier USR3510

Бренд: Patton Страницы: 181

Бренд: B&B Electronics Страницы: 60

Бренд: RTA Страницы: 73

Бренд: Yacht Devices Страницы: 32

INKNXMIT015C000

Бренд: HMS Страницы: 32

NETcon D-G-64NE

Бренд: ZIEHL-ABEGG Страницы: 27

Бренд: ICP CON Страницы: 10

Бренд: LANSITEC Страницы: 25

MediaPack 1 Series

Бренд: AudioCodes Страницы: 10

MediaPack MP-112

Бренд: AudioCodes Страницы: 622

Бренд: BellEquip Страницы: 20

Бренд: Telecom FM Страницы: 7

EA_Gatekeeper 3 Series

Бренд: Elster Страницы: 10

Бренд: AirLive Страницы: 234

Бренд: AirLive Страницы: 247

Бренд: SmartRG Страницы: 3

Бренд: OpenVox Страницы: 82

Бренд: IAI Страницы: 125

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды