Unitech MS860G Скачать руководство пользователя

Страница: 38 / 81

MS860G WiFi Manual

SCANNER CONFIGURATION MANAGER

Bar Code Symbologies, continued

UPC-E

•

Enabled

toggles the ability for the scanner to read UPC-E on or

off.
Default is “Yes”.

•

Code ID

is a user-definable identification letter for UPC-E,

which is referred to in the “Use Code ID” function on page 25.
Default is letter “E”.

•

Send Leading Digit

toggles sending or not sending a leading

(‘start bar code’) digit.
Default is “Send”.

•

Send Check Digit

toggles sending or not sending a check

digit.
Default is “Send”.

•

Zero Expansion

adds 0s to the bar code output to change

the UPC-E output format (8 digits) to UPC-A format (12 digits).
Default is “No”.

•

Enable NSC=1

allows the output of a UPC-E bar code

containing a first digit (Number System Character) of “1”.
Default is “No”.

EAN-13

•

Enabled

toggles the ability for the scanner to read EAN-13 on

or off.
Default is “Yes”.

•

Code ID

is a user-definable identification letter for EAN-13,

which is referred to in the “Use Code ID” function on page 25.
Default is letter “F”.

•

Send Leading Digit

toggles sending or not sending a leading

(‘start bar code’) digit.
Default is “Send”.

•

Send Check Digit

toggles sending or not sending a check

digit.
Default is “Send”.

•

Bookland EAN

toggles whether or not to send the EAN-13

bar code data in Bookland EAN (ISBN) format.
Default is “No”.

Содержание MS860G


















































































Результаты поиска

Содержание MS860G

Отзывы:

Похожие инструкции для MS860G

Бренды по названию

Популярные бренды

Unitech MS860G, Руководство пользователя

Результаты поиска

Содержание MS860G

Отзывы:

Похожие инструкции для MS860G

Бренды по названию

Популярные бренды