Unitech MS860G Скачать руководство пользователя | Manualshive

Страница: 31 / 81

background image

MS860G WiFi Manual

27

SCANNER CONFIGURATION MANAGER

Scanner Port, continued

Aim Function for Long Range Engine

The Aim function causes a laser scanner to output a “pin-point”
aiming aid for a specified period of time (see below) to enable a
user to more easily scan distant bar code labels.
Default is “No”.

Aiming Time for Long Range Engine

The Aiming Time function specifies the duration of the Aim
Function (see above) The length of duration can be specified
from 500ms to 2 seconds, in half-second increments.
Default is “1 second”.

Preamble

Insert a string of characters prior to the actual scanned data.
Pre-defined characters include:

•

<t> Tab

•

<r> Carriage

Return

•

<n> Line

Feed

•

<d>

Any Digit (data editing)

•

<a>

Any Letter (data editing)

•

<*>

Interblock Delay (data editing)

•

<“> (quotation

marks)

•

<dd>

Character in hexadeximal notation

•

<<>

< (less than)

•

<>>

> (greater than)

The above special characters must be bracketed by < > symbols
as shown.
Function codes (F keys, cursor up, Enter, etc.) can also be
inserted via hexadecimal code (accessable in a linked menu)
and must include surrounding brackets (<>).
Letters and numbers should be entered directly by keyboard
input without surrounding brackets (<>).
Default is “None”.

Postamble

Identical to Preamble (above), but characters are inserted after
scanned data. A common postamble would be to insert a “Tab”
in lieu of an “Enter” terminator (see page 24).
Default is “None”.

«
...
29
30
31
32
33
...
»

Содержание MS860G


















































































Отзывы:

Нет отзывов

Похожие инструкции для MS860G

Бренд: Gallagher Страницы: 13

Бренд: Kanguru Страницы: 1

Бренд: Kantech Страницы: 2

Бренд: Wasp Страницы: 27

Бренд: Harbor Freight Tools Страницы: 36

Бренд: Netum Страницы: 26

Бренд: Symbol Страницы: 352

Бренд: RTscan Страницы: 28

Бренд: Unitech Страницы: 2

PRS-505/LC - Portable Reader System

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

PRS-350SC - Reader Pocket Edition&trade

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

PRS-300BC - Reader Pocket Edition

Бренд: Sony Страницы: 2

PRS-300 - Reader Pocket Edition&trade

Бренд: Sony Страницы: 2

PRS-300 - Reader Pocket Edition PRS-300LC - Reader Pocket Edition PRS-300

Бренд: Sony Страницы: 2

PRS-600 - Electronic Book Reader

Бренд: Sony Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды