Unitech MS860G Скачать руководство пользователя страница 32

Страница: 32 / 81

MS860G WiFi Manual

SCANNER CONFIGURATION MANAGER

Bar Code Symbologies

Modify the output characteristics of 16 of the most popular bar
code symbologies in current use. Following are the bar code
symbologies and their modifiable parameters.

Code 39

•

Enabled

toggles the ability for the scanner to read Code 39 on or

off.
Default is “Yes”.

•

Code ID (Standard)

is a user-definable identification letter for

Standard Code 39, which is referred to in the “Use Code ID”
function on page 25.
Default is letter “M”.

•

Code ID (Full ASCII)

is the same as Code ID (Standard),

above, except that the symbology is Full ASCII Code 39.
Default is also letter “M”.

•

Type

toggles Code 39 between Standard and Full ASCII.

Default is “Full ASCII”.

•

Check Digit

defines whether or not a check digit (to insure

data accuracy) is calculated, and if so, whether it should be
sent or not.
Default is “Not Calculate”.

•

Send Start/Stop

toggles sending or not sending start/stop

sentinels (* in the case of Code 39).
Default is “No Send”.

•

Minimum Length

defines the minimum length the user will

accept for a valid bar code.
Default is “0”.

•

Maximum Length

defines the maximum length the user will

accept for a valid bar code.
Default is “48”.

Содержание MS860G


















































































Результаты поиска

Содержание MS860G

Отзывы:

Бренды по названию

Популярные бренды

Unitech MS860G, Руководство пользователя

Результаты поиска

Содержание MS860G

Отзывы:

Бренды по названию

Популярные бренды