Unitech MS860G Скачать руководство пользователя

Страница: 36 / 81

MS860G WiFi Manual

SCANNER CONFIGURATION MANAGER

Bar Code Symbologies, continued

MSI / Plessey Code

•

Enabled

toggles the ability for the scanner to read MSI /

Plessey Code on or off.
Default is “Yes”.

•

MSI Code ID

is a user-definable identification letter for MSI

Code, which is referred to in the “Use Code ID” function on
page 25.
Default is letter “O”.

•

Plessey Code ID

is the same as MSI Code ID (above) but

instead applicable to Plessey Code.
Default is letter “P”.

•

Send Check Digit

toggles whether or not to send a check

digit.
Default is “No Send”.

•

Check Digit Formula

defines the formula to calculate the

check digit. Options are:

Double Module 10
Module 11 Plus 10
Single Module 10

Default is “Double Module 10”.

•

Minimum Length

defines the minimum length the user will

accept for a valid bar code.
Default is “10”.

•

Maximum Length

defines the maximum length the user will

accept for a valid bar code.
Default is “64”.

Code 93

•

Enabled

toggles the ability for the scanner to read Code 93

on or off.
Default is “Yes”.

•

Code ID

is a user-definable identification letter for Code 93,

which is referred to in the “Use Code ID” function on page 25.
Default is letter “L”.

•

Minimum Length

defines the minimum length the user will

accept for a valid bar code.
Default is “1”.

•

Maximum Length

defines the maximum length the user will

accept for a valid bar code.
Default is “48”.

Содержание MS860G


















































































Результаты поиска

Содержание MS860G

Отзывы:

Похожие инструкции для MS860G

Бренды по названию

Популярные бренды

Unitech MS860G, Руководство пользователя

Результаты поиска

Содержание MS860G

Отзывы:

Похожие инструкции для MS860G

Бренды по названию

Популярные бренды