Unipulse M525B Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 85

background image

66

7

　

TROUBLESHOOTING

66

OPTION

Chapter

7

A ribbon cassette has not been installed, or the ribbon cassette is out of ink.

Referring to "2-1.Installing a Ribbon Cassette" on page 7, install or replace the
ribbon cassette.

SI/F signals from the load cell indicator include indicated and various kinds of weight
data irrespective of the value indicated by the indicator at that time.

elect data to be printed on the printer side. Set referring to "Print Data Selection Ach/
Bch" (page 19).

7-3.

The Printer Does not Function Properly

Counts are stored in battery-required memory. If the power is turned off and on again
with the battery exhausted, a problem occurs such that printing is not counted
normally.

The battery needs to be replaced. Since the battery should be replaced by
UNIPULSE, contact your dealer representative. The average life of the battery is
approx. 8 years. The time may also be incorrect if the battery is exhausted.

The decimal point position printed by the M252B depends on that of the indicator
side. If the decimal point position on the indicator side is changed during printing,
sub totals / grand totals are not calculated properly.

Never change the decimal point position of the indicator during printing. Change the
decimal point position after finding grand totals and clearing print data.

Data to which over status (R print) is added is not added.

Check that over status (R print) is not added to the print data.
The over status occurs due to indicator side trouble. Troubleshoot it referring to the
instruction manual of the indicator.

Although the printer head is running, nothing is printed.

Trouble 4

Cause 1

Remedy1

Values different from those indicated by the load cell indicator are printed.

Trouble 5

Cause 1

Remedy1

Printed counts are wrong.

Trouble 1

Cause 1

Remedy1

Values of sub totals / grand totals are wrong.

Trouble 2

Cause 1

Remedy1

Cause 2

Remedy1

«
...
73
74
75
76
77
...
»

Содержание M525B






















































































Отзывы:

Нет отзывов

Похожие инструкции для M525B

Бренд: WANHAO Страницы: 29

Бренд: Magicard Страницы: 26

Бренд: QMS Страницы: 194

Бренд: Z Corporation Страницы: 4

Бренд: Xerox Страницы: 108

4150S - WorkCentre B/W Laser

Бренд: Xerox Страницы: 4

Бренд: Canon Страницы: 30

Бренд: Canon Страницы: 18

MultiPASS MPC190

Бренд: Canon Страницы: 8

Бренд: Kodak Страницы: 2

Бренд: idp Страницы: 104

Бренд: Olivetti Страницы: 149

Бренд: NBS Technologies Страницы: 64

Бренд: idp Страницы: 48

Бренд: Kashino Technology Страницы: 72

Бренд: Axiohm Страницы: 6

Бренд: SIGN RACER Страницы: 73

Бренд: Copystar Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды