Unipulse M525B Скачать руководство пользователя страница 24

Страница: 24 / 85

FOR GREATER USE OF THE PRINTER

FOR GREATER USE OF THE PRINTER

Chapter

4-1.

Basics of Settings

■

Mode Configuration of The M252B

The M252B consists of four modes. See the "8-1.Setting Mode List" on page 68.

■

Setting Method of The M252B

The M252B adopts an interactive manner for making various settings. The current set value is
indicated by printing. You (user) should input a response with keys to proceed with the setting.

FOR GREATER USE OF THE PRINTER

Print mode

Setting mode

Printing is produced in
this mode. The M252B
starts with this mode
after power is turned on.

Printer settings are made
in this mode.

Option setting mode

Option settings are made
in this mode. You cannot
enter this mode if no
option is equipped.

＋

----------------

Quit

----------------

When

key is pushed,

“Quit”

is printed.

Maintenance mode

Maintenance of the
printer is performed in
this mode.

S e l e c t

Input with setting keys

Setting OK

M252B

Current set value

Changed set value

Содержание M525B






















































































Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды

Unipulse M525B, Руководство по эксплуатации

Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды