Unipulse M525B Скачать руководство пользователя страница 27

Страница: 27 / 85

FOR GREATER USE OF THE PRINTER

FOR GREATER USE OF THE PRINTER

Chapter

The changed set value is printed.

Cautions in setting

Some setting items are dependent on one another such that one setting does not become valid or
cannot be made until another setting is turned ON.
The setting items having a mutual dependence are shown below.

Dependence between settings

Source setting

Target setting

Description

06: Print Every ON/OFF

07: Print Every Format

The Print Every Format setting is not valid
until the Print Every ON/OFF setting is
turned [ON].

07: Print Every Format

20: Batch Total ON/OFF

If the Print Every Format setting is made at
[8], [9] or [10], the Batch Total ON/OFF
setting cannot be turned [ON].

20: Batch Total ON/OFF

07: Print Every Format

The Print Every Format setting [8], [9] or
[10] cannot be selected until the Batch Total
ON/OFF setting is turned [OFF].

22: Code Selection

24: Code Table Selection

Ach

25: Code Table Selection

Bch

The Code Table (A/Bch) setting cannot be
made until the Code Selection setting is
made at [2] or [3].

End --> ESC
Next --> Number-ENT
Change --> ENT

NOW ==> Off
09:Interval Print On/Off
--------------------------
New ==> Off

After changing the setting, go to the next setting (step 2 and 3).

To end the setting mode:

To make the Interval Print ON/OFF setting:

To make other settings:

This part is for the next
setting (09 : Interval Print
ON/OFF).

[ESC]

[Setting No.]

→

[ENT]

Changed set value

Содержание M525B






















































































Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды

Unipulse M525B, Руководство по эксплуатации

Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды