Unipulse M525B Скачать руководство пользователя страница 62

Страница: 62 / 85

ADVANCED USE

ADVANCE

D USE

Chapter

Since a list of items in the maintenance mode is printed, select a target item.

Cautions in maintenance mode

In the maintenance mode, each operation starts as soon as selection is made from the above menu
([item No.]

→

(ENT)). A confirmation message as in the setting mode and in the option

setting mode are not printed.
The test mode is an item for a factory check. Do not use this mode. (It is password-locked.)

--------------------------
Cancel/End

-->ESC

Test Mode

-->5-ENT

Parameter List

-->4-ENT

Self Test

-->3-ENT

Sample Print

-->2-ENT

Test Print

-->1-ENT

--------------------------
--------------------------

Maintenance

==========================

operating

To perform a test printing:

To perform a sample printing:

To perform a self test:

Since the item No. of Test Print is [1], press

(1)

→

(ENT).

As soon as

(ENT) is pressed, a test printing starts.

To print a parameter list:

To enter the test mode:

To cancel or end the maintenance mode:

[1]

→

[ENT]

[2]

→

[ENT]

[3]

→

[ENT]

[4]

→

[ENT]

[ESC]

Содержание M525B






















































































Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды

Unipulse M525B, Руководство по эксплуатации

Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды