Unipulse M525B Скачать руководство пользователя страница 26

Страница: 26 / 85

FOR GREATER USE OF THE PRINTER

FOR GREATER USE OF THE PRINTER

Chapter

Upon entry of the Automatic Print ON/OFF setting, the following is printed. The
current set value is indicated on the "NOW" line.

Since the following is subsequently printed, change the set value.

End

-->

ESC

-->

Number-ENT

Change-> -->

ENT

Now => ON
08:Automatic Print
--------------------------
>> Next is 08

operating

To make the Automatic Print setting:

To make other settings:

To end the setting mode:

The current value is "Automatic Print ON".
Change the set value to "OFF".

For changing the set value, develop an input waiting state
with the

(ENT) key.

[ENT]

[Setting No.]

→

[ENT]

[ESC]

Current set value

> Input new number - ENT

End

-->

ESC

-->

Number-ENT

Change-> -->

ENT

Now => ON
08:Automatic Print
--------------------------

To change

operating

This part is printed.
The following lines
are printed with "3".

Since the OFF set value No. is [0], press

(0)

→

(ENT).

[Setting No.]

→

[ENT]

About setting Nos.

Setting Nos. facilitate identification of each setting.
See detailed explanations of each setting or the appendix "8-1.Setting Mode List"
on page 68.

Point

Содержание M525B






















































































Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды

Unipulse M525B, Руководство по эксплуатации

Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды