Unipulse M525B Скачать руководство пользователя страница 70

Страница: 70 / 85

ADVANCED USE

ADVANCE

D USE

Chapter

■

Range Over (U/L)

If the range set under Target Value Ach (Bch) and Range Ach (Bch) is exceeded, the print is added
after printed data. If the upper limit is exceeded, "U" is printed, and if the lower limit is exceeded,
"L" is printed.

(Example) When the target value is set at 100, and the range at 20.

100

120

Lower Target Upper

L print

U print

55.0kgL etc

150.0kgU etc

‘U’ print
Measurement value > Target value + Range
‘L’ print
Measurement value < Target value - Range

limit

value

limit

EFGHI

68kgL

EFGHI

142kgU

EFGHI

121kgU

EFGHI

89kg

EFGHI

107kg

EFGHI

79kgL

EFGHI

120kg

Lower limit exceeded

Upper limit exceeded

------------------------
GT　　　　　　　　 726kg
COUNT               7
CODE           EFGHI
DATE   2000/07/04 02:36

--- GRAND TOTAL Ach ---

GT (grand total)

- If range over (U/L) and over status (R) (See the preceding page.) occur at the

same time, over status (R) is printed.

- Range over is a guide for users to know whether or not printed values exceed

the range. Sub totals and grand totals are not affected.

Point

Содержание M525B






















































































Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды

Unipulse M525B, Руководство по эксплуатации

Результаты поиска

Содержание M525B

Отзывы:

Похожие инструкции для M525B

Бренды по названию

Популярные бренды