UNI-T UPO1000CS Series Скачать руководство пользователя страница 81

Страница: 81 / 99

Figure 13-7

Click the confirmation after the input is completed, it can continuous to access according to the new

modified frp proxy IP address information (in correct configuration)

Note:

If each oscilloscope is connect with the same frp server, then web_port

，

pic_port

，

ctrl_port of each

oscilloscope should be consistent , otherwise frp proxy fails and cannot access.

If frp proxy is modified, it cannot access by local area network IP: 9000. If user need to recover the

normal access, press the DEFAULT button on the oscilloscope panel to reset the configuration and then

use IP: 9000 port to access.

(4) Password Setting

Password setting is for the user account to log in. After the user changes the login password, the

user needs to use the new password for the next login. If you forget the password, reset the

password by pressing the DEFAULT button on the oscilloscope panel.

Содержание UPO1000CS Series




































































































Результаты поиска

Содержание UPO1000CS Series

Отзывы:

Похожие инструкции для UPO1000CS Series

Бренды по названию

Популярные бренды

UNI-T UPO1000CS Series, Руководство пользователя

Результаты поиска

Содержание UPO1000CS Series

Отзывы:

Похожие инструкции для UPO1000CS Series

Бренды по названию

Популярные бренды