UNI-T UPO1000CS Series Скачать руководство пользователя страница 21

Страница: 21 / 99

(8) Function Key

(9)

①

MEASURE: Press this key to enable the measurement setting menu. It can set the measurement

source, parameter measurement, user-defined parameter, measurement statistic, measure indicator

and digital voltmeter. Turn on user-defined, it has 36 types of parameter measurement. Press

Multipurpose knob to quick select parameter to measuring and the result will show on the bottom of

the screen.

②

ACQUIRE

：

Press this key to enter sampling setting menu, it can set sampling mode, deep storage

and quick sampling.

③

CURSOR

：

Press this key to enter cursor measurement menu, it can set type of cursor measurement,

information source and mode.

④

DISPLAY

：

Press this key to enter the display setting menu to set the display type, format, grid

brightness, waveform brightness, backlight brightness, persistence time, color temperature, anti-

color temperature, menu display and transparency.

⑤

STORAGE

：

Press this key to enter storage interface. Storage type includes setting, waveform,

reference waveform and picture. It can also call back waveform and setting from storage. It can save

in internal or external USB device.

⑥

UTILITY

：

Press this key to enter the auxiliary function setting menu. It can set auto-calibration,

system information, language setting, waveform recording, pass/fail test, square wave output,

frequency meter, output selection, time setting, IP setting, boot loading and delete data, etc.

Содержание UPO1000CS Series




































































































Результаты поиска

Содержание UPO1000CS Series

Отзывы:

Похожие инструкции для UPO1000CS Series

Бренды по названию

Популярные бренды

UNI-T UPO1000CS Series, Руководство пользователя

Результаты поиска

Содержание UPO1000CS Series

Отзывы:

Похожие инструкции для UPO1000CS Series

Бренды по названию

Популярные бренды