UNI-T UPO1000CS Series Скачать руководство пользователя страница 60

Страница: 60 / 99

8.3 All Parameters Measurement

Press MEASURE to pop out all parameter to measuring all parameters, as shown in Figure 8-1.

Figure 8-1

All parameters are always marked the same color with the current measuring channel (the main source).

When "----" is shown, it indicates that the current source has no signal input, or the measurement result

is not valid range (too large or too small).

8.4 User Defined Parameters

Press MEASURE to pop out user defined, as shown in Figure 8-2.

Figure 8-2

Rotating the Multipurpose knob to select parameter and press the knob to confirm. For every selected

parameter, a * symbol will appear in front of the parameter. The user defined parameter will display on

the bottom of the screen, it can measuring 5 parameters at the same time.

User can select difference value, extremum to measuring statistic the user-defined parameters.

Содержание UPO1000CS Series




































































































Результаты поиска

Содержание UPO1000CS Series

Отзывы:

Похожие инструкции для UPO1000CS Series

Бренды по названию

Популярные бренды

UNI-T UPO1000CS Series, Руководство пользователя

Результаты поиска

Содержание UPO1000CS Series

Отзывы:

Похожие инструкции для UPO1000CS Series

Бренды по названию

Популярные бренды