UNI-T UPO1000CS Series Скачать руководство пользователя

Страница: 15 / 99

4.1 General Inspection

It is recommended to inspect the instrument follow the steps below before using the UPO1000CS series

for the first time.

(1) Check for Damages caused by Transport

If the packaging carton or the foam plastic cushions are severely damaged, please contact the UNI-T

distributor of this product immediately.

(2) Check Attachment

Please check appendix for the list of accessories. If any of the accessories are missing or damaged,

please contact UNI-T or local distributors of this product.

(3) Machine Inspection

If the instrument appears to be damaged, not working properly, or has failed the functionality test,

please contact UNI-T or local distributors of this product.

If the equipment is damaged due to shipping, please keep the packaging and notify both the

transportation department and UNI-T distributors, UNI-T will arrange maintenance or replacement.

4.2 Before Use

To perform a quick verification of the instrument’s normal operations, please follow the steps below

：

(1) Connect to the Power Supply

The power supply voltage range is from 100 VAC to 240 VAC, the frequency range is 50/60Hz.

Connect the oscilloscope to the power supply line that came with the oscilloscope or any power

supply line that meets the local country standards. Turn on the power button, which on the back of

the oscilloscope. The soft power button

in the front of the oscilloscope should be on red. Press

this button to turn on the oscilloscope.

(2) Boot Check

Press the soft power button

and the light should change to green. The oscilloscope will show

a boot animation, and then enter the normal interface.

(3) Connect Probe

Use probe in the attachment and connect it BNC port to the channel 1 BNC port of the oscilloscope.

Connect the pro

be’s main alligator clip to the “Compensating signal port” and the ground clip is

connected to the “Ground terminal” shown below. The output of the compensating signal should be
amplitude 3Vpp, default frequency is 1 kHz.

Содержание UPO1000CS Series




































































































Результаты поиска

Содержание UPO1000CS Series

Отзывы:

Похожие инструкции для UPO1000CS Series

Бренды по названию

Популярные бренды

UNI-T UPO1000CS Series, Руководство пользователя

Результаты поиска

Содержание UPO1000CS Series

Отзывы:

Похожие инструкции для UPO1000CS Series

Бренды по названию

Популярные бренды