UNI-T UPO1000CS Series Скачать руководство пользователя

Страница: 19 / 99

4.5 Operation Panel

(1) Vertical Control

①

CH1

、

CH2

：

Analog channel setting keys, CH1, CH2 identified by different

colors and it also corresponding to the colors of waveforms on the screen and

channel input connectors. Press any key to turn on the related channel menu

(activate or disable channel).

②

MATH

：

Press this key to open the mathematical operation menu for add,

subtract, multiply, divide, FFT, logical operations, digital filtering and advanced

operations.

③

Vertical POSITION

：

Adjust the vertical position to move the current channel

waveform, the vertical offset value

will display at the baseline cursor.

Press this knob to return the channel display back to the vertical midpoint.

④

Vertical SCALE

：

Vertical position knob is used for adjusting the vertical scale,

turn clockwise to decrease the scale, turn counterclockwise to increase the scale.

With this process, waveform will display increasing or decreasing and position

information

will also be presented at the same time. The vertical

scale stepped as 1-2-5 order. Press the knob allows the vertical adjustment to

switch between coarse and fine adjustment mode.

(2) Horizontal Control

①

HORI MENU

：

Horizontal menu is for display window extension, Multi-

Scopes, timebase (XY/YT) and trigger holdoff.

②

Horizontal POSITION

：

Adjusting the horizontal position knob, the trigger

point moves around the left or right of the center of the screen, and the

waveform of all the channel moves to left or right. Horizontal position

parameter

will display on the top of the screen in real- time. Press

this knob to return the channel display back to the midpoint position.

③

Horizontal SCALE

：

Used to adjust the time base of all the channel. Screen

will display the changes of the waveform, compressed or extension on

horizontal. Time base

will display on the top of the screen in

real- time. The time base scale stepped as 1-2- 5 order. Press the knob

allows the horizontal adjustment to switch between window display and

extension window.

Содержание UPO1000CS Series




































































































Результаты поиска

Содержание UPO1000CS Series

Отзывы:

Похожие инструкции для UPO1000CS Series

Бренды по названию

Популярные бренды

UNI-T UPO1000CS Series, Руководство пользователя

Результаты поиска

Содержание UPO1000CS Series

Отзывы:

Похожие инструкции для UPO1000CS Series

Бренды по названию

Популярные бренды