UGSI Encore 700 Скачать руководство пользователя страница 63

Страница: 63 / 125

CF.440.400.001.IM.0417

ENCORE

700 METERING PUMP

Figure 4-2. Stroke Control Alignment

n. Push the knob past the O-ring for manual position (quad-ring for auto-

matic position) until the front edge of the knob is in line with the zero
percent line on the stroke control housing scale.

o. Slide the knob, if necessary, to align the scales as shown in Figure 4-2.

Tighten the three M6 set screws (48) equally. Make sure the set screws
that are used have a Nylok

™

patch on the threads to prevent oil leakage.

NOTE: All O-rings must be lightly lubricated with silicone grease before
assembly.

• Gearbox Cover Installation for Direct Drive (refer to Dwg. 440.400.001.010

and 440.400.000.010)

a. Position the inner assembly (cone) of the lower tapered roller bearing

(7, Dwg. 440.400.000.010) onto the smaller end of the worm shaft
(51, Dwg. 440.400.000.010) Install the outer race (cup) of the bearing
into the gearbox. Place the bearing cone, with the worm shaft, into the
bearing cup.

b. Install shims (12,14 &15 on Dwg. 440.400.000.010) and tapered, roller

bearing (6) cone onto the worm shaft.

c. Temporarily install the cover (with bearing cup and oil seal)
tightening the four bolts closest to the worm shaft.

d. Check that end play is within .005". If not, select and install proper

shims.

e. Remove the cover and apply grease (8, Dwg. 440.400.000.010) to the

top bearing.

f. Apply 1/8" bead of RTV adhesive (3, Dwg. 440.400.001.010) around

the top lip of the gearbox.

Содержание Encore 700






























































































































Результаты поиска

Содержание Encore 700

Отзывы:

Похожие инструкции для Encore 700

Бренды по названию

Популярные бренды

UGSI Encore 700, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Encore 700

Отзывы:

Похожие инструкции для Encore 700

Бренды по названию

Популярные бренды