UGSI Encore 700 Скачать руководство пользователя страница 59

Страница: 59 / 125

CF.440.400.001.IM.0417

ENCORE

700 METERING PUMP

a. Remove the gearbox cover, as described in step a, above.

b. Drain the gearbox oil.

c. Remove the worm shaft assembly (51) by pulling it up.

NOTE: Two bearings (6) and (7) and a shim combination (12-15) come out
with the assembly.

d. Set the knob (47) to zero.

e. Remove the gear access ﬂ ange (2) by unscrewing the four M8 screws

(3).

f. Slide the drive gear (50) and the drive bushing assembly (4) out through

the ﬂ ange opening.

NOTE: Mark the position of the drive gear (50) or drive bushing (4)
relative to the sheave (46) so that they can be reassembled at the same
position.

g. On a bench, remove the tapered roller bearing (30) from the drive bush-

ing (4).

h. Unscrew the ﬁ ve M6 screws (10) and remove the drive gear (50).

• Worm Shaft and Drive Gear Replacement (refer to Dwg. 440.400.000.010A)

a. Apply Blue Loctite thread locker (11) to the ﬁ ve M6 screws (10). Re-

place the drive gear (50) and secure with screws (10).

b. Reverse the above removal procedures for replacement of the worm

shaft and the drive gear.

• Eccentric Assembly, Tapere Roller Bearings, Connecting Rod, Stroke Con-

trol Housing, and Knob Removal (refer to Dwg. 440.400.000.010A&B)

a. Follow steps a through d of the procedure for worm shaft and drive

gear removal, above.

b. Remove the stroke control knob (47) by loosening the three set screws

(48) just enough to slide the knob out. Do not screw all the way out,
just ﬂ ush with the surface of the knob.

NOTE: If the pump is equipped with an electric stroke positioner, refer to
the applicable instruction manual.

NOTE: The set screws (48) are coated with Nylok

™

to seal. If set

screws were removed or are leaking, replace with a new one.

Содержание Encore 700






























































































































Результаты поиска

Содержание Encore 700

Отзывы:

Похожие инструкции для Encore 700

Бренды по названию

Популярные бренды

UGSI Encore 700, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Encore 700

Отзывы:

Похожие инструкции для Encore 700

Бренды по названию

Популярные бренды