UGSI Encore 700 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 125

background image

CF.440.400.001.IM.0417

ENCORE

®

700 METERING PUMP

16

2.1

General Information

To provide satisfactory service, the metering pump must be installed in accor-
dance with the instructions that follow. Operational diﬃ

culties, lack of accuracy,

and possible damage to the pump mechanism may occur if these instructions
are not followed properly.

2.2

Unpacking

When the pump is unpacked, check all items against the packing list to make
sure that no parts are discarded with the packaging material. Whenever possible,
unpack the equipment at the installation site.

2.3

Mounting the Pump

Pump location is important to the operation of the pump. Select a place that is
dry and that provides a level base for the pump. Allow work space around the
pump for inspection, adjustments, and servicing (refer to Dwgs. 440.400.110.010
or 440.400.110.020). Be sure it is near a power supply and located where the
discharge line may be conveniently run to the point of application. The pump may
be installed with a ﬂ ooded suction arrangement (refer to Dwg. 440.400.110.040).
A carefully considered and correct installation will help provide satisfactory
performance.

When installing the equipment, proceed as follows:

a. Select the appropriate dimension and/or installation drawing to be sure the lo-

cation selected will meet all requirements. Refer to Dwgs. 440.400.110.010,
020, 030, and 040.

b. Mount the pump on the bench, shelf, or level pad on which it will be located.

c. Connect to a power supply matching the characteristics speciﬁ ed on the

motor nameplate and in accordance with local electrical code requirements.
Suﬃ

cient ﬂ exibility must be provided in the

connection to permit adjustments. Be sure to provide a shut-oﬀ switch in
the power supply.

NOTE: Field wiring must conform to local electrical codes.

WARNING: TO AVOID POSSIBLE SEVERE PERSONAL INJURY OR
DAMAGE TO THE EQUIPMENT CONSULT YOUR UGSI CHEMI-
CAL FEED, INC. REPRESENTATIVE IF THE PUMP IS TO BE USED
UNDER CONDITIONS OTHER THAN ORIGINALLY SPECIFIED
OR IF THERE IS ANY QUESTION REGARDING THE SIZE OF
THE DISCHARGE LINE.

!

«
...
30
31
32
33
34
...
»

Содержание Encore 700






























































































































Отзывы:

Нет отзывов

Похожие инструкции для Encore 700

Бренд: Calpeda Страницы: 44

Бренд: Calpeda Страницы: 64

Бренд: Calpeda Страницы: 32

Бренд: Larius Страницы: 46

Бренд: Annovi Reverberi Страницы: 18

COBRA DS 0600 E

Бренд: BUSCH Страницы: 24

Бренд: Warren rupp Страницы: 22

AquaMax Eco Expert 20000/12V

Бренд: Oase Страницы: 231

Бренд: Wilden Страницы: 43

Бренд: Dantherm Страницы: 17

SWUP EXT Series

Бренд: Sunsystem Страницы: 16

Бренд: Giant Страницы: 12

EWAA0 DAV3P Series

Бренд: Daikin Страницы: 240

Warren Rupp SANDPIPER Beast SPB20

Бренд: Idex Страницы: 21

Бренд: T Therm Geo Страницы: 53

Бренд: Rheem Страницы: 52

Бренд: BGS technic Страницы: 12

Бренд: Pentair Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды