UFactory xArm 5 Скачать руководство пользователя страница 124

Страница: 124 / 182

124

【

zero position

】

●

The robotic arm returns to a posture where the joint value are 0.

【

move joint J1() J2() J3 () J4() J5() J6() J7() Radius() Wait(true/false) ,[move] ,

[edit]

】

●

Set each joint value for the joint movement, with the unit of degree.

【

move(arc) line X() Y()Z() Roll() Pitch() Yaw() Radius() Wait(true/false) [move]

[edit]

】

●

Set the Cartesian coordinate target value of the linear motion and the TCP rotation

angle in mm and °.

【

move (front/back/left/right) (true/false)() mm

】

●

Indicates that the robotic arm makes relative linear motion

forward/backward/left/right based on the current position, in mm

【

move tool line X() Y()Z() Roll() Pitch() Yaw() Radius() Wait(true/false)

】

●

This command is a relative motion relative to TCP coordinates.

【

move circle position 1 to position 2

】

●

From current position, the whole circle is determined by current position and

position1 and positon2, “center angle” specifies how much of the circle to execute.

【

center angle (°) ()

】

●

Indicates the degree of the circle. When it is set to 360, a whole circle can be

completed, and it can be greater than or less than 360; (Note: To achieve smooth
track motion, you need to set Wait = false).

【

move joint [variable] J1() J2() J3 () J4() J5() J6() J7() Wait(true/false)

】

●

The command passes through the joint motion and supports variable values.

Содержание xArm 5























































































































































































Результаты поиска

Содержание xArm 5

Отзывы:

Похожие инструкции для xArm 5

Бренды по названию

Популярные бренды

UFactory xArm 5, Руководство пользователя

Результаты поиска

Содержание xArm 5

Отзывы:

Похожие инструкции для xArm 5

Бренды по названию

Популярные бренды