Ublox MAX-M10S Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 89

background image

MAX-M10S - Integration manual

products inside the GNSS receiver front-end that fall into the GNSS band and contribute to in-band
interference.

Measures against out-of-band interference include maintaining a good grounding concept in the
design and adding a GNSS band-pass ﬁlter into the antenna input line to the receiver.

Out-of-band blocking immunity

and

Out-of-band rejection

provide more

information about the RF immunity of the MAX-M10S module and how to mitigate such
interference.

3.2.3 Spectrum analyzer

The UBX-MON-SPAN message can be enabled in u-center to provide a low-resolution spectrum
analyzer suﬃcient to identify noise or jammers in the reception band. Once enabled, u-center
includes a real-time chart that is updated once per second with the message data. See

for an example.

The shape of the spectrum as well as any RF interference in the form of a spur or intermodulation
product can be easily analyzed with this graphical tool. The vertical axis compares the amplitude
diﬀerence in dB for each frequency. A good spectrum shape is characterized by an even noise ﬂoor
along with the GNSS band. For example, if any unwanted spur stands out, the vertical axis gives a
rough approximation of the power level in dB compared to the noise ﬂoor.

Next to the chart, the center frequency, span, and resolution values set for the spectrum, and the
PGA value are also displayed. The PGA value represents the internal gain set by the receiver, which
depends on the external ampliﬁcation of the GNSS input signal.

The vertical discontinuous lines in the chart area represent the oﬀset to the center frequency in
MHz. This helps to estimate the frequency of any spurious emission seen.

In addition, u-center includes three functions commonly found in any spectrum analyzer. These
features support the RF front-end design and help to spot out any jammer presence during the
application operation.

• View / hold: if selected, the current spectrum shape freezes in a colored line. This allows for a

comparison between the time the spectrum was frozen and the real-time spectrum. This is
particularly helpful in assessing the impact of running other onboard components.

• Average: if selected, a colored line shows the averaged spectrum for each frequency. This

supports the analysis over time and obtaining a less noisy shape.

• Max hold: if selected, a colored line shows the maximum amplitude measured at each

frequency. This option helps to spot out any jammer over a period of time.

shows the spectrum view in u-center with the view/hold option selected. The redish line

represents the frozen spectrum before modifying the external gain, while the black line represents
the current measurement.

UBX-20053088 - R03

3 Hardware integration

Page 65 of 89

C1-Public

«
...
63
64
65
66
67
...
»

Содержание MAX-M10S


























































































Отзывы:

Нет отзывов

Похожие инструкции для MAX-M10S

Бренд: MadgeTech Страницы: 4

wM-Bus 868 USB Key

Бренд: MADD Страницы: 4

Бренд: Onkyo Страницы: 20

Бренд: JETStream Страницы: 62

Бренд: Spektrum Страницы: 16

Gear Lite FDB-9649-ST

Бренд: Ross Страницы: 22

Бренд: IMG STAGELINE Страницы: 24

Бренд: R&S Страницы: 223

Бренд: PCB Piezotronics Страницы: 17

Digital Freeview Receiver

Бренд: Tevion Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Advance Paris Страницы: 16

MASTER Progress 4ER42E10-33

Бренд: GE Страницы: 51

Бренд: Hallicrafters Страницы: 13

Бренд: Channel Vision Страницы: 8

Бренд: Johnson Controls Страницы: 4

Бренд: Phonocar Страницы: 20

POWERPACK BE490

Бренд: RingGrip Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды