Ublox MAX-M10S Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 89

background image

MAX-M10S - Integration manual

Figure 37: Typical 1.8 V design

B.2 Antenna supervisor designs

and

show a reference design for a 2-pin and 3-pin antenna supervisor design

respectively. Here are some key features:
• VCC and V_IO are connected together to a single supply.
• Supply at V_BCKP is optional. If present, the hardware backup mode is supported. This mode

maintains the time and GNSS orbit data in the battery-backed RAM memory if the main supply
is switched oﬀ.
If there is no backup supply, the EXTINT pin can be used for time aiding and the GNSS orbit data
can be aided using AssistNow services or downloaded to the host and fed back to the receiver
at startup.

• An external SAW ﬁlter can be placed on the RF path as shown in

, which allows an SAW-

LNA-SAW RF front-end circuit for improving out-of-band immunity against RF interference from
other sources. This is especially useful when MAX-M10S is used in cellular applications.

• An active antenna can be supplied with the VCC_RF output from MAX-M10S or from an external

supply. VCC_RF is a ﬁltered output voltage supply, which outputs VCC - 0.1 V. In addition, the
active antenna supply can be turned on/oﬀ by the LNA_EN signal, which also controls the internal
LNA of MAX-M10S.

• External open drain buﬀers and operational ampliﬁers are also needed depending on whether a

2-pin or 3-pin antenna supervisor design is used.

• UART and I2C communication interfaces are available. I2C PIOs (SDA and SCL) can be used in a

3-pin antenna supervisor design as shown in

. In this case, the I2C interface needs to be

disabled before assigning the new function to the PIOs.

Disable the I2C interface with the CFG-I2C-ENABLED conﬁguration key when I2C pins are
used for antenna supervisor functions. Likewise, disable the UART interface (CFG-UART1-
ENABLED) or TIMEPULSE (CFG-TP-TP1_ENA) when the pins are used for antenna supervisor
functions.

UBX-20053088 - R03

Appendix

Page 83 of 89

C1-Public

«
...
81
82
83
84
85
...
»

Содержание MAX-M10S


























































































Отзывы:

Нет отзывов

Похожие инструкции для MAX-M10S

Бренд: Xantech Страницы: 4

Бренд: Icom Страницы: 3

Бренд: Badger Meter Страницы: 4

Бренд: Kathrein Страницы: 64

Бренд: Icom Страницы: 16

New Jersey MP68

Бренд: Blaupunkt Страницы: 400

Бренд: B&K Страницы: 12

Бренд: Harman Kardon Страницы: 9

Бренд: Galaxy Innovations Страницы: 48

Бренд: BASETech Страницы: 48

Бренд: Yaesu Страницы: 64

Бренд: Dual Страницы: 1

Бренд: Pace Страницы: 55

Бренд: OrangeRx Страницы: 2

Бренд: Metra Electronics Страницы: 8

Бренд: Kramer Страницы: 19

GEN VI RADIO P1110

Бренд: Daktronics Страницы: 34

Бренд: TowiTek Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды