Ublox MAX-M10S Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 89

background image

MAX-M10S - Integration manual

• ANT_DETECT = active high. The pin is default high (PIO pull-up enabled, to be pulled low if the

antenna is not detected).

Startup message at power-up if the conﬁguration is stored:

$GNTXT,01,01,02,ANTSUPERV=AC SD OD PDoS SR*15

$GNTXT,01,01,02,ANTSTATUS=INIT*3B

$GNTXT,01,01,02,ANTSTATUS=OK*25

ANTSUPERV=AC SD OD PDoS SR

(indicates open circuit detection added - OD)

If ANT_DETECT is pulled low to indicate no antenna connected:

$GNTXT,01,01,02,ANTSTATUS=OPEN*35

If ANT_DETECT is left ﬂoating or pulled high to indicate antenna connected:

$GNTXT,01,01,02,ANTSTATUS=OK*25

2.4.1.7 Antenna status reporting

The antenna detection and antenna power status that is available in UBX-MON-RF and NMEA notice
messages, is based on the antenna's physical state. The required antenna supervisor conﬁguration
keys depend on the selected antenna supervisor implementation (three-pin or two-pin).

and

present a summary of the antenna status that is available in the

antStatus

and

antPower

ﬁelds of the UBX-MON-RF message. Refer to the interface description [

] for more

information.

Status

Description

DON'T KNOW

Antenna status is unknown.

INIT

Antenna power control feature is initialized (if CFG-HW-ANT_VOLTCTRL is enabled).

SHORT

A short is detected from the antenna input. That is, a lot of current is drawn from the active antenna.

OPEN

Antenna is not detected. That is, little or no current is drawn from the active antenna.

OK

Antenna is detected and no short is detected.

Table 17: Available antenna detection status

Status

Description

DON'T KNOW

CFG-HW-ANT_VOLTCTRL not conﬁgured.

OFF

GNSS OFF or a short is detected and CFG-HW-ANT_PWRDOWN is enabled. Note that this status
also applies when GNSS is restarted via CFG-RST or implicitly via CFG-GNSS, when GNSS selection is
reconﬁgured, or when GNSS is stopped in software standby mode and the oﬀ state of the power save
mode on/oﬀ (PSMOO).

ON

GNSS ON and no short/open is detected from the antenna input. Similarly, when there is a short and
CFG-HW-ANT_PWRDOWN is not enabled or auto-recovery is enabled.

Table 18: Available antenna power status

shows some possible combinations of the antenna supervisor conﬁguration and the

expected antenna status based on the physical state of the antenna. Note that the short detection
takes priority over the open detection and "X" in

implies an unconﬁgured or undetected

physical state. In addition, CFG-HW-ANT_PWRDOWN requires that CFG-HW-ANT_CFG_VOLTCTRL
and CFG-HW-ANT_CFG_SHORTDET are enabled. Likewise, CFG-HW-ANT_RECOVER requires CFG-
HW-ANT_PWRDOWN to be enabled.

The antenna supervisor is re-initialized after issuing a reset with RESET_N pin or changing
any of the antenna supervisor conﬁguration keys. Therefore, if the default conﬁguration has

UBX-20053088 - R03

2 Receiver functionality

Page 31 of 89

C1-Public

«
...
29
30
31
32
33
...
»

Содержание MAX-M10S


























































































Отзывы:

Нет отзывов

Похожие инструкции для MAX-M10S

Бренд: Harman Kardon Страницы: 11

Бренд: Harman Kardon Страницы: 8

Бренд: Harman Kardon Страницы: 9

Бренд: Harman Kardon Страницы: 3

Бренд: Harman Kardon Страницы: 2

Бренд: Harman Kardon Страницы: 2

Бренд: Harman Kardon Страницы: 18

Бренд: Harman Kardon Страницы: 32

Бренд: Harman Kardon Страницы: 50

Бренд: Icom Страницы: 24

Бренд: Icom Страницы: 2

Бренд: Jensen Страницы: 12

VM9213 - Touch Screen MultiMedia Receiver

Бренд: Jensen Страницы: 62

Бренд: Jensen Страницы: 9

Бренд: Jensen Страницы: 22

JHD3510 - Heavy Duty CD Receiver

Бренд: Jensen Страницы: 2

VM8013HD - Screen MultiMedia Receiver

Бренд: Jensen Страницы: 78

Phase Linear UV10

Бренд: Jensen Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды