Ublox MAX-M10S Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 89

background image

MAX-M10S - Integration manual

Figure 34: Soldering proﬁle

Modules

must not

be soldered with a damp heat process.

Optical inspection

After soldering the module, consider optical inspection.

Cleaning

Do not clean with water, solvent, or ultrasonic cleaner:

• Cleaning with water will lead to capillary eﬀects where water is absorbed into the gap between

the baseboard and the module. The combination of residues of soldering ﬂux and encapsulated
water leads to short circuits or resistor-like interconnections between neighboring pads.

• Cleaning with alcohol or other organic solvents can result in soldering ﬂux residues ﬂowing

underneath the module, into areas that are not accessible for post-cleaning inspections. The
solvent will also damage the sticker and the printed text.

• Ultrasonic cleaning will permanently damage the module, in particular the quartz oscillators.

The best approach is to use a “no clean” soldering paste to eliminate the cleaning step after the
soldering.

Repeated reﬂow soldering

Repeated reﬂow soldering processes or soldering the module upside down are not
recommended.

A board that is populated with components on both sides may require more than one reﬂow
soldering cycle. In such a case, the process should ensure the module is only placed on the board
submitted for a single ﬁnal upright reﬂow cycle. A module placed on the underside of the board may
detach during a reﬂow soldering cycle due to lack of adhesion.

The module can also tolerate an additional reﬂow cycle for rework purposes.

Wave soldering

Base boards with combined through-hole technology (THT) components and surface-mount
technology (SMT) devices require wave soldering to solder the THT components. Only a single wave
soldering process is encouraged for boards populated with modules.

Rework

UBX-20053088 - R03

4 Product handling

Page 77 of 89

C1-Public

«
...
75
76
77
78
79
...
»

Содержание MAX-M10S


























































































Отзывы:

Нет отзывов

Похожие инструкции для MAX-M10S

Бренд: Accurate Technology Страницы: 20

Бренд: L&S Страницы: 5

Бренд: Yamaha Страницы: 57

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 60

Бренд: Axxera Страницы: 28

Бренд: Teac Страницы: 56

Бренд: Majestic Страницы: 13

Centronic VarioControl VC420

Бренд: Becker Страницы: 52

Бренд: CEBEK Страницы: 2

Бренд: R&S Страницы: 112

Бренд: Rock Mars Страницы: 18

Бренд: Sansui Страницы: 44

Бренд: BDStar Страницы: 44

Бренд: Nokeval Страницы: 38

Бренд: Harman Kardon Страницы: 39

Бренд: Akai Страницы: 15

Бренд: B&K Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды