Ublox MAX-M10S Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 89

background image

MAX-M10S - Integration manual

• The operation of the

AssistNow Autonomous

feature is transparent to the user and the

operation of the receiver. All calculations are done in the background and do not aﬀect the
normal operation of the receiver.

• The

AssistNow Autonomous

subsystem automatically invalidates data that has become too old

and that would introduce unacceptable positioning errors. This threshold is conﬁgurable.

• The prediction quality will be automatically improved if the satellite has been observed multiple

times. However, this requires the availability of a suitable ﬂash memory (not available in MAX-
M10S) . Improved prediction quality also extends the maximum usability period of the data.

•

AssistNow Autonomous

considers GPS, GLONASS, Galileo and BeiDou satellites only. It will not

consider satellites on orbits with an eccentricity of >0.05 (e.g., Galileo E18). For GLONASS
support, a suitable ﬂash memory is mandatory because a single GLONASS broadcast
ephemeris contains information only for approximately 30 minutes. This is not long enough
to extend it in a usable way. Orbit information of each GLONASS satellite must be collected at
least for four hours to generate data.

Flash memory is not available in MAX-M10S.

2.13.4.2 Interface

Several UBX protocol messages provide interfaces to the

AssistNow Autonomous

feature:

• The CFG-ANA-USE_ANA item is used to enable or disable the

AssistNow Autonomous

feature.

When enabled, the receiver will automatically produce

AssistNow Autonomous

data for newly

received broadcast ephemerides and, if that data is available, automatically provide the
navigation subsystem with orbits when necessary and adequate.

• The CFG-ANA-* conﬁguration group also allows for a conﬁguration of the maximum acceptable

orbit error. See the next section for an explanation of this feature. It is recommended to use the
ﬁrmware default value that corresponds to a default orbit data validity of approximately three
days (for GPS satellites observed once) and up to six days (for GPS and GLONASS satellites
observed multiple times over a period of at least half a day).

UBX-20053088 - R03

2 Receiver functionality

Page 57 of 89

C1-Public

«
...
55
56
57
58
59
...
»

Содержание MAX-M10S


























































































Отзывы:

Нет отзывов

Похожие инструкции для MAX-M10S

Бренд: Hallicrafters Страницы: 12

Бренд: Hallicrafters Страницы: 15

Бренд: Hallicrafters Страницы: 37

Бренд: Hallicrafters Страницы: 78

Бренд: Cadillac Страницы: 102

Бренд: Sangean Страницы: 52

Бренд: EisSound Страницы: 5

Бренд: Onkyo Страницы: 99

Бренд: Tecsun Страницы: 34

Бренд: Yanglousi Technology Страницы: 3

Бренд: Vertex Страницы: 32

Бренд: SYD Страницы: 9

Бренд: AFi Страницы: 4

Бренд: AMG Страницы: 6

Бренд: Streetwize Страницы: 5

Бренд: Yaesu Страницы: 3

Digital Freeview Receiver

Бренд: Tevion Страницы: 2

Бренд: Hallicrafters Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды