Tynetec Entel Ultra Скачать руководство пользователя страница 7

Страница: 7 / 44

Doc No. FM0713 Issue C Page 7

4. SYSTEM NODES

Entel Ultra system nodes (telephone or video) are housed in IP65 rated lockable steel enclosures. These

includes a fused mains termination block, a low voltage switch mode power supply unit, an auto-BST trade

timeclock and either 1 or 2 distribution/video add-on boards. Leads are provided for an optional 12V 7.0Ah

rechargeable battery.

4.01 SYSTEM NODE OPTIONS

There are 4 models of system node; 8 or 16 port for standard telephone systems and 8 or 16 port for video

systems, see part numbers below;

TYNETEC P/No. DESCRIPTION

ZE508I

Entel Ultra 8 Port System Node

ZE516I

Entel Ultra 16 Port System Node

ZV508I

Entel Ultra 8 Port Video System Node

ZV516I

Entel Ultra 16 Port Video System Node

4.02 INSTALLATION

The system node should be located in a dry, secure area which is easily accessible for termination and future

service. The cable entry plate is normally on the top with the door hinged on the left hand side. The door can

be swapped to hinge from the right or the back plate can be inverted if the cable entry plate is required on the

bottom. Always ensure proprietary cable glands are used to maintain the IP65 rating of the enclosure.

4.03 EARTH BONDING

All door entry metalwork e.g. system node cabinet, door panel backbox & fascia, fireman’s switches, etc. must

be bonded to the Mains Earth terminal using a minimum of 2.5 mm

cable.

4.04 MAINS SUPPLY

The 240V AC mains connection should be taken from the landlords supply and terminated in the fused screw

terminal block provided in the system node. Replacement fuse = 3A (1 inch domestic mains type).

Distribution Board 1

Output Ports 1-8

with green Active and

red Fault LED’s

Trade

Timeclock

SMPSU and

Battery

Protection

Board

Fused Mains

Termination

Block

ZE516I

16 PORT SYSTEM NODE

IP65 Lockable

Steel Enclosure

Dimensions:

400x300x150mm

(HxWxD)

Video system nodes have an additional

8 port video add-on board fitted alongside

the distribution board(s)

Distribution Board 2

Output Ports 9-16

with green Active and

red Fault LED’s

Содержание Entel Ultra













































Результаты поиска

Содержание Entel Ultra

Отзывы:

Похожие инструкции для Entel Ultra

Бренды по названию

Популярные бренды

Tynetec Entel Ultra, Руководство по установке

Результаты поиска

Содержание Entel Ultra

Отзывы:

Похожие инструкции для Entel Ultra

Бренды по названию

Популярные бренды