Tykma ELECTROX Minilase Скачать руководство пользователя страница 4

Страница: 4 / 29

Minilase™ e

System Guide

3 |

P a g e

Getting Started

Thank you for purchasing the Minilase™ e laser marking system. Minilase™ e is

shipped fully assembled and is completely operational within 15 minutes. Most
laser marking systems require elaborate, time consuming setup, plus complex

assembly and training sessions. But Minilase™ e changes all of that. Let’s get

started!

Your Minilase™ is shipped fully assembled in one box. Minilase™ is a desktop

system, so you should arrange a suitable workbench or desk area. You will
need:

An area 17” (432mm) wide x 34” (864mm) deep with at least 50”

(1,270mm) of headroom to accommodate the system footprint.

Ample room next to the system for a laptop or desktop PC, monitor,

keyboard and mouse. You will be installing Minilase™ Pro SE software
on your PC to program and run Minilase™.

Items included with your system
(Note; all files located on USB drive)

Minimum computer requirements

USB drive labeled with system
serial number

Software (USB drive)

System

guide, you’re reading

it!

Minilase™ Pro SE software

manual

Video tutorials

Laser programming guide

Laser safety manual

One (1) power cord

One (1) USB cable

Windows™ XP Pro, 7 Pro, 8 or

Pentium 4 processor or
greater

80GB hard drive storage or
greater

2GB RAM or greater

USB 2.0 or greater

Содержание ELECTROX Minilase






























Результаты поиска

Содержание ELECTROX Minilase

Отзывы:

Похожие инструкции для ELECTROX Minilase

Бренды по названию

Популярные бренды

Tykma ELECTROX Minilase, Системное руководство

Результаты поиска

Содержание ELECTROX Minilase

Отзывы:

Похожие инструкции для ELECTROX Minilase

Бренды по названию

Популярные бренды