Turin TKB80306 Скачать руководство пользователя

Страница: 74 / 90

Chapter 6 System parameters

6.1 Basic Settings

All the parameter settings in this section change the basic parameters of the robot,

which will affect the use of the robot. Before setting the parameters, you must confirm the

correctness of the steps and parameters before saving.

The basic setting interface of the teach pendant is shown below. The basic settings

include zero point calibration, link parameters, joint parameters, space parameters,

20-point calibration, and robot model. These parameters are not recommended for the

operator to change at will. Improper modification will cause the robot to work abnormally.

Therefore, it is recommended that manufacturers use this interface to set parameters before

debugging.

6.1.1 Zero calibration

On the zero calibration interface, the following figure shows the current encoder value

and current joint angle. The right-most column is to calibrate the zero point calibration of

each axis or all axes. The zero point is not allowed to be modified by the customer.

Figure 6-1 Zero calibration

6.1.2 Connecting rod parameters

The link parameters of each robot are different. The following figure shows the link

parameters of the robot. These parameters are not allowed to be modified by the customer.

Содержание TKB80306



























































































Результаты поиска

Содержание TKB80306

Отзывы:

Похожие инструкции для TKB80306

Бренды по названию

Популярные бренды

Turin TKB80306, Техническое руководство

Результаты поиска

Содержание TKB80306

Отзывы:

Похожие инструкции для TKB80306

Бренды по названию

Популярные бренды