Turin TKB80306 Скачать руководство пользователя

Страница: 37 / 90

The position data records the current position information of the robot, and records

the position information while recording the motion instruction.

The motion type specifies the trajectory between the teaching points during execution.

Robots generally support three types of motion: joint motion (MOVJ), linear motion

(MOVL), and circular motion (MOVC).

Movement speed refers to the speed at which the robot performs movement between

the teaching points.

To add motion commands, press the "Enable" switch to enable the drive.

1) Types of joint motion

When the robot does not need to move to the current teaching point with the specified

path, the joint motion type is adopted. The motion command corresponding to the joint

motion type is

【

joint motion]

】

(English command: MOVJ). In general, for safety, the joint

motion type is used at the beginning of the program.

The characteristics of the joint motion type are the fastest speed and the unknown path.

Therefore, this type of motion is generally used at a spatial point, and before running the

program automatically, it must be checked at a low speed to observe whether the actual

trajectory of the robot interferes with the surrounding equipment.

The operation of adding the

【

Joint Motion

】

command is as follows.

Click

【

Add Instruction

】

【

Motion Instruction

】

【

Joint Motion

】

, enter the relevant

parameters such as speed, acceleration, smoothing and tool, user coordinates, and then

click the

【

New

】

button.

Figure 3-16 Joint command

The established command is shown in the figure below. The current teaching position

becomes the end point of the joint motion.

Содержание TKB80306



























































































Результаты поиска

Содержание TKB80306

Отзывы:

Похожие инструкции для TKB80306

Бренды по названию

Популярные бренды

Turin TKB80306, Техническое руководство

Результаты поиска

Содержание TKB80306

Отзывы:

Похожие инструкции для TKB80306

Бренды по названию

Популярные бренды