manualshive.com logo in svg

TRONTEQ ROQSTAR 006-130-100, Руководство пользователя, Страница: 28 / 37

Поделиться
Скачать
TRONTEQ ROQSTAR 006-130-100 Скачать руководство пользователя страница 28

User Manual ROQSTAR  
Support: www.tronteq.de/support 
Release 11/2016 

 

Page 28 of 37

 

13.  Device information  

13.1.  LED display 

 

 

With the LED display, you can perform an initial, rapid device diagnosis. 

 

System Status LED 

These LEDs indicate the status of the device. The LED display is replicated in the web interface. Their 
meaning is described in the table below. 
 

Order No. 006-130-100 

 LED 

Color 

Activity 

Operational State 

V1 

- 

off 

power supply V1 is not connected 

green 

lights up 

power supply V1 is connected 

V2 

- 

off 

power supply V2 is not connected 

green 

lights up 

power supply V2 is connected 

 

Order No. 006-130-101/102

 

 LED 

Color 

Activity 

Operational State 

PWR 

- 

off 

Power supply is not connected. 

green 

lights up 

Power supply is connected, device is supplied with power. 

green 

flashes with 1Hz 

Indicates an error of the redundant power supply.  

MOD 

- 

off 

Device is off, out of service or device is booting. 

green 

lights up 

Device is ready to operate. 

green 

flashes with 1Hz 

Active web interface session. 

green 

flashes with 
10Hz 

Firmware update is being performed or 
configuration is loaded / saved. 

ERR 

- 

off 

There is no error, device operates properly. 

red 

flashes with 1Hz 

Configuration error: 
- false user configuration 

red 

lights up 

Fatal system error. Device is not ready to operate due to: 
- memory errors 
- not recognized Switch / Phy - 
- error in an internal voltage 

 
 

Port LED 

Each network port has two LEDs. Their meaning is given in the table below. 
 

LED 

Color 

Activity 

Operational State 

Link 

- 

none 

no network connection, Link-Down 

green 

lights up 

network connection, Link-Up 

Act 

- 

none 

no data transfer 

yellow 

flashes 

data transfer with 10/100 MBit / s 

 
 
 
 

 

Содержание ROQSTAR 006-130-100






































Отзывы:

Нет отзывов