Triton TAMAS Скачать руководство пользователя

Страница: 22 / 28

SPARE PARTS

NOTE:

Not all wiring has been shown for reasons of clarity.

SPARE PARTS

Thermal cut-out ............................22012020

Control PCB ....................................7073333

Heater can assembly with NRV

.....................

8.5kW ...........................................83314610
9.5kW ...........................................83314620

Solenoid valve ............................P26810801

Pressure switch assembly ............P26810803

Thermostatic...............................P26810807

Temperature control

Pressure relief device (PRD) ...........82800450

Terminal block & wires ...............S26811001

Water inlet ......................................7054085

10.

Water Outlet ...............................P26810802

11.

Main Trimplate

White..............................................7054071
Black ...............................................7054075

12.

Signal wire ......................................2160611

13.

Cover ass (including ON/OFF switch & PCB)

White..........................................S26820602
Black ...........................................S26820603

Bottom pipe trim
White..............................................7054073
Black ...............................................7054077

Top pipe trim
White..............................................7054072
Black ...............................................7054076

Heat inlet valve assembly
8.5kW .........................................S26810805
9.5kW .........................................S26810810

Содержание TAMAS





























Результаты поиска

Содержание TAMAS

Отзывы:

Похожие инструкции для TAMAS

Бренды по названию

Популярные бренды

Triton TAMAS, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TAMAS

Отзывы:

Похожие инструкции для TAMAS

Бренды по названию

Популярные бренды