background image

Triton Showers 

Triton Road 

Nuneaton 

Warwickshire  CV11 4NR

Triton is a division of Norcros Group (Holdings) Limited

TRITON reserve the right to change product specification without prior notice. E&OE. © TRITON SHOWERS 2012

Customer Service: 

0844 980 0750

Trade Installer Hotline: 

0844 980 0730 

Fax: 

 

0844 980 0744

www.tritonshowers.co.uk 

E-mail: [email protected]

TRITON STANDARD GUARANTEE

Triton guarantee this product against all mechanical defects 
arising from faulty workmanship or materials for a period of 
five years for domestic use only, from the date of purchase, 
provided that it has been installed by a competent person in full 
accordance with the fitting instructions. 
Any part found to be defective during this guarantee period 
we undertake to repair or replace at our option without 
charge so long as it has been properly maintained and 
operated in accordance with the operating instructions, and 
has not been subject to misuse or damage. 
This product must not be taken apart, modified or repaired 
except by a person authorised by Triton. This guarantee 
applies only to products installed within the United Kingdom 
and does not apply to products used commercially. This 
guarantee does not affect your statutory rights. 

What is not covered: 
1.

  Breakdown due to: 

a)

 use other than domestic use by 

you or your resident family; 

b)

 wilful act or neglect; 

c)

 any 

malfunction resulting from the incorrect use or quality of 
electricity, gas or water or incorrect setting of controls; 

d)

 

failure to install in accordance with this installation guide. 

2.

  Claims for missing parts once the product has been 

installed.

3.

  Repair costs for damage caused by foreign objects or 

substances.

4.

  Total loss of the product due to non-availability of parts.

5.

  Compensation for loss of use of the product or 

consequential loss of any kind.

6.

  Call out charges where no fault has been found with the 

appliance.

7. 

Call out charges where the water supply cannot be 
isolated, this includes consequential losses arising from 
unserviceable supply valves.

8. 

The cost of repair or replacement of pressure relief 
devices, showerheads, hoses, riser rails and/or wall 
brackets, isolating switches, electrical cable, fuses and/or 
circuit breakers or any other accessories installed at the 
same time.

9. 

The cost of routine maintenance, adjustments, overhaul 
modifications or loss or damage arising therefrom, 
including the cost of repairing damage, breakdown, 
malfunction caused by corrosion, furring, pipe scaling, 
limescale, system debris or frost.

8-8-2012

UK SERVICE POLICY

In the event of a product fault or complaint occurring, the following 

procedure should be followed:

1. 

Telephone Customer Service on 

0844 980 0750

 having available, 

your details including post code, the model number and power 

rating of the product, together with the date of purchase and, where 

applicable, details of the particular fault.

2. 

If required, the Customer Service Advisor will arrange  

for a qualified engineer to call.

3.

  All products attended to by a Triton service engineer must be installed 

in full accordance with the Triton installation guide applicable to the 

product. 

(Every product pack contains an installation guide, however, 

they can also be bought via our Customer Service Spares Department)

.

4.

  Our engineer will require local parking and if a permit is required this 

must be available to the engineer on arrival at the call. 

5.

  It is essential that you or an appointed representative 

(who must 

be over 18 years of age)

 is present for the duration of the service 

engineer's visit. If the product is in guarantee you must produce proof 

of purchase.

6.

  Where a call under the terms of guarantee has been booked and 

the failure is not product related 

(i.e. scaling and furring, incorrect 

water pressure, pressure relief device operation or electrical/plumbing 

installation fault)

 a charge will be made. A charge will also be issued 

if nobody is at home when the service engineer calls or adequate 

parking/permit is not available.

7.

  If the product is no longer covered by the guarantee an up front fixed 

fee will be charged before the site visit.

8.

  Should proof of purchase not be available on an “in-guarantee” call, 

or should the service engineer find that the product is no longer 

under guarantee, the engineer will charge the same fixed price and 

the customer will be expected to pay the engineer before he leaves. 

If payment is not made on the day an administration charge will be 

added to the fixed charge.

9.

  If a debt is outstanding from a previous visit, or from any other Triton 

purchase. Triton reserves the right to withhold service until the debt 

has been settled.

10.

  Triton takes the health, safety and wellbeing of its employees very 

seriously and expects customers to treat all staff members with respect. 

Should any employee feel threatened or receive abuse, either verbally 

or physically, Triton reserves the right to withhold service and will 

support the employee with a legal prosecution.

Replacement Parts Policy

It is the policy of Triton Showers to maintain parts availability for the 

duration of production and a period of 5 years thereafter in accordance 

with industry standards. In the event of a spare part not being available a 

substitute part will be supplied.
Spare parts can be ordered via our online spare parts store, or by 

telephoning Triton Spares Department. Payment should be made by 

credit/debit card 

(excluding American Express or Diners Card)

. Payment 

can also be made by pre-payment of a pro-forma invoice, by cheque or 

postal order.
Telephone orders are based on information given during of the call. Before 

contacting Triton, please verify your requirements using the information 

contained in the user guide. Triton cannot accept liability for incorrect part 

identification.

For the latest Terms & Conditions, please see: 

www.tritonshowers.co.uk

Содержание KAHO





















Отзывы: