background image

Manual mixer shower

To check the product suitability for commercial and multiple installations, please contact Triton’s 
specification advisory service before installation.

Telephone:

Facsimile:

E mail:

0844 980 0730
0844 980 0744
[email protected]

CONTENTS Page

Main components .......................................................................... 1

Introduction ................................................................................... 2
Site requirements ........................................................................... 2
Safety warnings .............................................................................. 2
Plumbing requirements .................................................................. 2
Water system requirements ............................................................ 2

Typical suitable installations ..........................................................4 - 5

Siting of the shower ....................................................................... 6

Fitting the mixer ............................................................................. 7

Building-in depth ............................................................................ 8

Solid wall, hollow wall and panel mounting .................................8 - 9

Fitting the bulkhead pipework ....................................................... 10
Leak testing ................................................................................... 10
Making good  ................................................................................ 10

Fitting the cover plate ................................................................... 11
Fitting the control lever ................................................................. 11
Bulkhead assembly ........................................................................ 11

Commissioning .............................................................................. 12
Operating the shower.................................................................... 12
Cleaning ........................................................................................ 12

Flow chart ..................................................................................... 13

Dimensions .................................................................................... 14

Spare parts .................................................................................... 15

Fault finding .................................................................................. 16

Guarantee, service policy, etc. ..................................................rear cover

Содержание KAHO





















Отзывы: