Trinamic TMCM-1021 TMCL Скачать руководство пользователя страница 70

Страница: 70 / 109

TMCM-1021 TMCL

™

Firmware Manual • Firmware Version V1.42 | Document Revision V1.10 • 2018-JAN-09

70 / 109

3.7.35

RETI (Return from Interrupt)

This command terminates an interrupt handling routine. Normal program ﬂow will be continued then.

This command is intended for use in standalone mode only.

An interrupt routine must always end with a RETI command. Do not allow the normal program ﬂow to run

into an interrupt routine.

Internal function:

The saved registers (accumulator, X registers, ﬂags and program counter) are copied

back so that normal program ﬂow will continue.

Related commands:

EI, DI, VECT.

Mnemonic:

RETI

Binary Representation

Instruction

Type

Motor/Bank

Value

0 (don’t care)

Reply in Direct Mode

Status

Value

100 - OK

don’t care

Example

Return from an interrup handling routine.

Mnemonic:

RETI

Binary Form of RETI

Field

Value

Target address

Instruction number

Type

Motor/Bank

Value (Byte 3)

Value (Byte 2)

Value (Byte 1)

Value (Byte 0)

Checksum

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1021 TMCL














































































































Результаты поиска

Содержание TMCM-1021 TMCL

Отзывы:

Похожие инструкции для TMCM-1021 TMCL

Бренды по названию

Популярные бренды

Trinamic TMCM-1021 TMCL, Руководство пользователя

Результаты поиска

Содержание TMCM-1021 TMCL

Отзывы:

Похожие инструкции для TMCM-1021 TMCL

Бренды по названию

Популярные бренды