Trinamic TMCM-1021 TMCL Скачать руководство пользователя страница 29

Страница: 29 / 109

TMCM-1021 TMCL

™

Firmware Manual • Firmware Version V1.42 | Document Revision V1.10 • 2018-JAN-09

29 / 109

3.7.5

SAP (Set Axis Parameter)

With this command most of the motion control parameters of the module can be speciﬁed. The settings

will be stored in SRAM and therefore are volatile. That is, information will be lost after power off.

Info

For a table with parameters and values which can be used together with this

command please refer to section

Internal function:

The speciﬁed value is written to the axis parameter speciﬁed by the parameter number.

Related commands:

GAP, AAP.

Mnemonic:

SAP <parameter number>, <axis>, <value>

Binary representation

Binary Representation

Instruction

Type

Motor/Bank

Value

see chapter

<value>

Reply in Direct Mode

Status

Value

100 - OK

don’t care

Example

Set the maximum positioning speed for motor 0 to 51200 pps.

Mnemonic:

SAP 4, 0, 51200.

Binary Form of SAP 4, 0, 51200

Field

Value

Target address

Instruction number

Type

Motor/Bank

Value (Byte 3)

Value (Byte 2)

Value (Byte 1)

Value (Byte 0)

Checksum

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1021 TMCL














































































































Результаты поиска

Содержание TMCM-1021 TMCL

Отзывы:

Похожие инструкции для TMCM-1021 TMCL

Бренды по названию

Популярные бренды

Trinamic TMCM-1021 TMCL, Руководство пользователя

Результаты поиска

Содержание TMCM-1021 TMCL

Отзывы:

Похожие инструкции для TMCM-1021 TMCL

Бренды по названию

Популярные бренды