Trinamic TMCM-1021 TMCL Скачать руководство пользователя страница 5

Страница: 5 / 109

TMCM-1021 TMCL

™

Firmware Manual • Firmware Version V1.42 | Document Revision V1.10 • 2018-JAN-09

5 / 109

Features

The TMCM-1021 is a single axis controller/driver module for 2-phase bipolar stepper motors with state

of the art feature set. It is highly integrated, offers a convenient handling and can be used in many

decentralized applications. The module can be mounted on the back of NEMA 11 (28mm ﬂange size)

stepper motors and has been designed for coil currents of up to 0.7A RMS and 24V DC supply voltage.

With its high energy eﬃciency from Trinamic’s coolStep™ technology cost for power consumption is kept

down. The TMCL ﬁrmware allows for standalone operation and direct mode control.

Main characteristics

• Motion controller & stepper motor driver:

–

On the ﬂy alteration of motion parameters (e.g. position, velocity, acceleration).

–

High performance microcontroller for overall system control and communication protocol

handling.

–

Up to 256 microsteps per full step.

–

High-eﬃcient operation, low power dissipation.

–

Dynamic current control.

–

Integrated protection.

–

stallGuard2™ feature for stall detection.

–

coolStep™ feature for reduced power consumption and heat dissipation.

• Encoder

–

sensOstep™ magnetic encoder with 1024 increments per round.

–

Usable for example for step-loss detection under all operating conditions and positioning

supervision.

• Interfaces

–

RS485 bus.

–

Up to four general-purpose digital inputs (two shared with general purpose outputs).

–

Two general purpose outputs.

–

Step/Direction input (shared with the general purpose inputs).

Software

TMCL remote controlled operation via RS485 interface and/or stand-alone operation via TMCL program-

ming. PC-based application development software TMCL-IDE available for free.

Electrical data

• Supply voltage: +24V DC nominal (10. . . 27V DC supply range).

• Motor current: up to 0.7A RMS / 1A peak (programmable). Since hardware V1.4 also 1.4A RMS / 2A

peak programmable (new extended range since hardware V1.4).

Please see also the separate Hardware Manual.

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1021 TMCL














































































































Результаты поиска

Содержание TMCM-1021 TMCL

Отзывы:

Бренды по названию

Популярные бренды

Trinamic TMCM-1021 TMCL, Руководство пользователя

Результаты поиска

Содержание TMCM-1021 TMCL

Отзывы:

Бренды по названию

Популярные бренды