Trinamic TMCM-1021 TMCL Скачать руководство пользователя страница 86

Страница: 86 / 109

TMCM-1021 TMCL

™

Firmware Manual • Firmware Version V1.42 | Document Revision V1.10 • 2018-JAN-09

86 / 109

All Global Parameters of the TMCM-1021 Module in Bank 0

Number

Global Parameter

Description

Range [Units]

Access

RS485 baud rate

9600

Default

14400

19200

28800

38400

57600

76800

115200

230400

0. . . 8

RWA

Serial address

Module (target) address for RS485.

1. . . 255

RWA

ASCII Mode

Conﬁgure the TMCL ASCII interface:

Bit 0

0 - start up in binary (normal) mode

1 - start up in ASCII mode

Bits 4 & 5

00 - Echo back each character

01 - Echo back complete command

10 - Do not send echo, only send com-

mand reply

0. . . 63

RWA

Serial heartbeat

Serial heartbeat for RS485 interface. If this

time limit is up and no further command is

received by the module the motor will be

stopped. Setting this parameter to 0 (de-

fault) turns off the serial heartbeat function.

0. . . 65535

RWA

Telegram pause

time

Pause time before the reply via RS485 is

sent. For use with older RS485 interfaces it

is often necessary to set this parameter to

15 or more (e.g. RS485 adapters controlled

by the RTS pin). For CAN interface this pa-

rameter has no effect!

0. . . 255

RWA

Serial host

address

Host address used in the reply telegrams

sent back via RS485.

0. . . 255

RWA

Auto start mode

0 - Do not start TMCL application after

power up (default).

1 - Start TMCL application automatically af-

ter power up.

0/1

RWA

End switch

polarity

0 - normal polarity

1 - reverse polarity

0/1

RWA

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1021 TMCL














































































































Результаты поиска

Содержание TMCM-1021 TMCL

Отзывы:

Бренды по названию

Популярные бренды

Trinamic TMCM-1021 TMCL, Руководство пользователя

Результаты поиска

Содержание TMCM-1021 TMCL

Отзывы:

Бренды по названию

Популярные бренды