Trinamic TMCM-1021 TMCL Скачать руководство пользователя страница 32

Страница: 32 / 109

TMCM-1021 TMCL

™

Firmware Manual • Firmware Version V1.42 | Document Revision V1.10 • 2018-JAN-09

32 / 109

3.7.8

RSAP (Restore Axis Parameter)

With this command the contents of an axis parameter can be restored from the EEPROM. By default, all

axis parameters are automatically restored after power up. An axis parameter that has been changed

before can be reset to the stored value by this instruction.

Info

For a table with parameters and values which can be used together with this

command please refer to section

Internal function:

The axis parameter speciﬁed by the type and bank number will be restored from the

EEPROM.

Related commands:

SAP, AAP, GAP, RSAP.

Mnemonic:

RSAP <parameter number>, <bank>

Binary Representation

Instruction

Type

Motor/Bank

Value

see chapter

0 (don’t care)

Reply in Direct Mode

Status

Value

100 - OK

0 (don’t care)

Example

Restore axis parameter #6.

Mnemonic:

RSAP 8, 6.

Binary Form of RSAP 8, 6

Field

Value

Target address

Instruction number

Type

Motor/Bank

Value (Byte 3)

Value (Byte 2)

Value (Byte 1)

Value (Byte 0)

Checksum

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1021 TMCL














































































































Результаты поиска

Содержание TMCM-1021 TMCL

Отзывы:

Похожие инструкции для TMCM-1021 TMCL

Бренды по названию

Популярные бренды

Trinamic TMCM-1021 TMCL, Руководство пользователя

Результаты поиска

Содержание TMCM-1021 TMCL

Отзывы:

Похожие инструкции для TMCM-1021 TMCL

Бренды по названию

Популярные бренды