Trinamic TMCM-1021 TMCL Скачать руководство пользователя страница 84

Страница: 84 / 109

TMCM-1021 TMCL

™

Firmware Manual • Firmware Version V1.42 | Document Revision V1.10 • 2018-JAN-09

84 / 109

Number

Axis Parameter

Description

Range [Units]

Access

214

Power down

delay

Standstill period before the motor current will be

switched to standby current. The default value

is 200 which means 2000ms.

1. . . 65535

[10ms]

RWE

215

Absolute

resolver value

Absolute position of the internal sensOstep en-

coder. The absolute position is within one motor

rotation.

0. . . 1023

254

Step/direction

mode

Normal mode. Step/dir mode off.

Use of the ENABLE inputs on step/dir

connector to switch between hold cur-

rent and run current (no automatic

switching) .

Automatic switching between hold and

run current: after the ﬁrst step pulse the

module automatically switches over to

run current, and a conﬁgurable time af-

ter the last step pulse the module auto-

matically switches back to hold current.

The ENABLE inputs on the step/dir con-

nector do not have any functionality.

Always use run current, never switch to

hold current. The ENABLE inputs on the

step/dir connector do not have any func-

tionality.

Automatic current switching like (2), but

the ENABLE inputs are used to switch the

driver stages completely off or on.

Always use run current like (3), but the

ENABLE pins are used to switch the

driver stages completely off or on.

0. . . 5

RWE

Table 15: All Axis Parameters of the TMCM-1021 Module

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1021 TMCL














































































































Результаты поиска

Содержание TMCM-1021 TMCL

Отзывы:

Бренды по названию

Популярные бренды

Trinamic TMCM-1021 TMCL, Руководство пользователя

Результаты поиска

Содержание TMCM-1021 TMCL

Отзывы:

Бренды по названию

Популярные бренды