Trinamic TMCM-1021 TMCL Скачать руководство пользователя страница 82

Страница: 82 / 109

TMCM-1021 TMCL

™

Firmware Manual • Firmware Version V1.42 | Document Revision V1.10 • 2018-JAN-09

82 / 109

Number

Axis Parameter

Description

Range [Units]

Access

193

Reference

search mode

Search left stop switch only.

Search right stop switch,

then

search left stop switch.

Search right stop switch,

then

search left stop switch from both

sides.

Search left stop switch from both

sides.

Search home switch in negative di-

rection, reverse the direction when

left stop switch reached.

Search home switch in positive di-

rection, reverse the direction when

right stop switch reached.

Search home switch in positive di-

rection, ignore end switches.

Search home switch in negative di-

rection, ignore end switches.

Additional functions:

• Add 128 to a mode value for inverting

the home switch (can be used with mode

5. . . 8).

• Add 64 to a mode for searching the right

instead of the left reference switch (can be

used with mode 1. . . 4).

1. . . 8

194

Reference

search speed

This value speciﬁes the speed for roughly search-

ing the reference switch.

0. . .

2147483647

[pps]

195

Reference

switch speed

This parameter speciﬁes the speed for searching

the switching point. It should be slower than

parameter 194.

0. . .

2147483647

[pps]

196

End switch

distance

This parameter provides the distance between

the end switches after executing the RFS com-

mand (with reference search mode 2 or 3).

-2147483648

. . . 2147483647

[µsteps]

197

Last reference

position

This parameter contains the last position value

before the position counter is set to zero during

reference search.

-2147483648

. . . 2147483647

[µsteps]

200

Boost current

Current used for acceleration and deceleration

phases. If set to 0 the same current as set by

axis parameter #6 will be used. Same scaling as

with axis parameter #6.

0. . . 255

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1021 TMCL














































































































Результаты поиска

Содержание TMCM-1021 TMCL

Отзывы:

Бренды по названию

Популярные бренды

Trinamic TMCM-1021 TMCL, Руководство пользователя

Результаты поиска

Содержание TMCM-1021 TMCL

Отзывы:

Бренды по названию

Популярные бренды