Trane Symbio 210 Скачать руководство пользователя страница 29

Страница: 29 / 76

BAS-SVX084A-EN

Controller LEDs

Binary B01 through
B05

Shows solid yellow.

Indicates a corresponding binary output has been
commanded ON.

• Relay coil: indicates that a command has been made to

energize.

• TRIAC: indicates that a command has been made to turn ON.

If you are currently powering the
Symbio 210 from a USB port, the
Led lights will turn ON. However,
the binary outputs will not be
activated.

Commanded ON; As an example of
commanded ON, a command could
be a manual command such as an
override or a command could be
from TGP2 based on a list of
conditions that are met telling these
outputs to turn ON.

LED not lit:
Did you command it to be ON? If
yes, see the

Table 9, p. 26

LED not lit.

Indicates that a relay output is de-energized or no power to
the board.

• Not lit: cycle power to reestablish communication.

Table 9.

LED activities and troubleshooting tips (continued)

LED Name

Activities

Indication and Troubleshooting Tips

Notes

Содержание Symbio 210













































































Результаты поиска

Содержание Symbio 210

Отзывы:

Похожие инструкции для Symbio 210

Бренды по названию

Популярные бренды

Trane Symbio 210, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Symbio 210

Отзывы:

Похожие инструкции для Symbio 210

Бренды по названию

Популярные бренды