Trane Symbio 210 Скачать руководство пользователя страница 23

Страница: 23 / 76

BAS-SVX084A-EN

Wiring Installation

The three values are joined together to form the BACnet device ID for the unit controller as shown
in the following table.

Device ID Assignment for BACnet/IP Devices

For devices connecting over BACnet/IP, Tracer SC+ calculates the device ID with the following:

•

The BACnet network number for the BACnet/IP link. (This number can be changed by the user).

•

The unit controller rotary switch value. (The Tracer SC+ rotary address is not used to calculate
BACnet/IP device IDs).

The following table shows this process using a Tracer UC600 unit controller.

Table 8.

Calculating the BACnet/IP Device ID

For BACnet MS/TP Network numbers higher than 4190,TTrraacceerr SSCC++ will not be able follow
this scheme and will not propose a Device ID for the unit controller. The controller can be installed
with the Device ID number previously assigned to it.

Note:

It is very important to avoid duplication of BACnet network numbers or device IDs.

Application Wiring

This section provides information about pre-configured wiring for the following applications:

•

“Zone Sensor Wiring”

•

“Duct Temperature Sensor Wiring,” p. 25

•

“Binary Wiring,” p. 26

Note:

For more details about mounting, wiring, and configuring wireless zone sensors, refer to the
section,

“Additional Resources,” p. 75

Zone Sensor Wiring

Zone Sensor Hard Wired Option

Depending on the zone sensor options used, a maximum of seven (7) wires may be required to run
from the Symbio

210 controller to the zone sensor. The zone sensor options are:

•

Zone sensor (temperature only);

Part Number X1351152801

•

Zone sensor with timed override (TOV) on/cancel button;

Part Number X1351153001

•

Zone sensor with adjustable setpoint thumbwheel,

Part Number X1351152901

•

Zone sensor with adjustable setpoint thumbwheel, timed override (TOV) on/cancel button;

Part Number X1351152701

•

Zone sensor with digital display;

Part Number X1379088601

Note:

Display sensor has factory mounted communication module.

•

Communications module;

Part Number X1365146702, one (1) box of 12

Table 7.

Calculating the BACnet Device ID

Tracer SC+ rotary switch value (21)

Tracer SC+ BACnet MS/TP link number (1)

Unit controller rotary switch value (38)

BACnet Device ID 211038

BACnet network number Eth port 1 (1)

Unit controller rotary switch value (42)

BACnet/IP Device ID: 0142

Содержание Symbio 210













































































Результаты поиска

Содержание Symbio 210

Отзывы:

Похожие инструкции для Symbio 210

Бренды по названию

Популярные бренды

Trane Symbio 210, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Symbio 210

Отзывы:

Похожие инструкции для Symbio 210

Бренды по названию

Популярные бренды