Trane Symbio 210 Скачать руководство пользователя страница 7

Страница: 7 / 76

BAS-SVX084A-EN

Overview

Controller Specifications and Dimensions

Table 1.

Controller storage, operating, and compliance information

Storage

Temperature: -67°F to 203°F (-55°C to 95°C)

Humidity: 5% to 95% (non-condensing)

Operating

Temperature: -40°F to 122°F (-40°C to 50°C)

Humidity: 5% to 95% (non-condensing)

Power:

20-4–27.6 Vac, (24 Vac ±15% nominal, 50–60 Hz, 10.5 VA). See

Table 5, p. 14

for

transformer sizing details.

Environmental Rating (Enclosure): NEMA 1

Pollution: U.L. 840: Degree 2

Agency Compliance

• UL916 PAZX- Open Energy Management Equipment

• UL94-5V Flammability

• UL2043 Plenum Rated (Plastic enclosure versions without actuators only)

• CE Marked

• FCC Part 15, Subpart B, Class B Limit

• VCCI-CSPR 32:2016

• CAN ICES-003(B)/NMB-003(B)

• Communications BACnet MS/TP, BACnet IP, or BACnet Zigbee (Air-Fi).

• The Symbio 210 is BACnet Testing Laboratory (BTL) certified to revision 15 of the ASHRAE BACnet-135 standard as a Building Controller (BC)

profile device.

• The European Union (EU) Declaration of Conformity is available from your local Trane® office.

Figure 1.

Dimensions (with actuator)

Содержание Symbio 210













































































Результаты поиска

Содержание Symbio 210

Отзывы:

Похожие инструкции для Symbio 210

Бренды по названию

Популярные бренды

Trane Symbio 210, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Symbio 210

Отзывы:

Похожие инструкции для Symbio 210

Бренды по названию

Популярные бренды