Trane Symbio 210 Скачать руководство пользователя страница 11

Страница: 11 / 76

BAS-SVX084A-EN

Overview

Device Inputs/Outputs

Below is a list of device inputs and outputs.

•

A twisted/shielded communication link

•

Zone sensor

•

Occupancy sensor (optional)

•

Discharge Air Temperature (DAT)

•

sensor

•

24 Vac, Class II power

Table 4

provides details for each type input/output.

Table 4.

Symbio

210 inputs and outputs

Analog Inputs 1 through 3

Note:

Configuration options when used as spare; 10k



thermistor, 0 to



linear setpoint, 200



to 20k



linear.

Universal Inputs UI1 and UI2

Note:

Configuration options when used as spare; 4–20mA, 0-10V,

resistive (see AI specifications), binary (solid state open collector)

•

AI1

: Space temperature; thermistor: 10k



@77°F (25°C) range: 32°F

to 122°F (0°C to 50°C)

•

AI2

: Space setpoint; potentiometer: 1k



from 50 to 90°F (10 to

32.2°C), */** (thumbwheel) functionality supported

•

AI3

: Discharge air temperature: 10k



@77°F (25°C) from -40°F to

212°F (-40 to 100°C)

•

UI1

: Relative Humidity

•

UI2

: CO

Pressure Input P1

Binary Input BI1, Dry Contact

•

: Supply air flow; pressure transducer: From 0 to 5 in. water column

(0 to 1245 Pa)

•

BI1

: Occupancy

Analog Outputs AO1 and AO2

Note:

Configuration options when used a spare; Voltage output is 0 to 10

VDC, 500 ohm min. impedance. Current output is 4 - 20 mA, 500



max. impedance.

Binary Outputs 1 through 5

Note:

0.5A Resistive Maximum Rating

•

AO1/B12

: ECM

•

AO2/B13

: SCR Heat/Waver Valve Signal

•

BO1:

Heat stage 3 TRIAC

•

BO2:

Heat stage 2/Water Valve Close TRIAC

•

BO3

: Heat stage 1/Water Valve Open TRIAC

•

BO4

: Air Damper Open TRIAC

•

BO5

: Air Damper Close TRIAC

Содержание Symbio 210













































































Результаты поиска

Содержание Symbio 210

Отзывы:

Похожие инструкции для Symbio 210

Бренды по названию

Популярные бренды

Trane Symbio 210, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Symbio 210

Отзывы:

Похожие инструкции для Symbio 210

Бренды по названию

Популярные бренды