Trane Symbio 210 Скачать руководство пользователя страница 31

Страница: 31 / 76

BAS-SVX084A-EN

Controller LEDs

Note:

*Patch firmware updates will cause the same error codes.

Red LED Blink
Pattern

Load Field Fail

Attempted load of the field kernel or device
tree failed.

1. Thumb drive with .scfx file,

power down, set address

rotaries to 991, and power up.

2. Replace controller.

Load Recovery Fail

Attempted load of the recovery image failed. Replace controller

Field Mount Fail

Failed to mount the field partition during a
firmware update attempt.

1. Thumb drive with .scfx file,

power down, set address

rotaries to 991, and power up.

2. Replace controller.

Bad Switch Setting

Rotary switches are set to a bad/unknown
value.

Contact technical support.

Bad Firmware File

Unable to mount the firmware update file.

Download firmware file again and
retry download.

Firmware Not Compatible

Firmware file downloaded is not compatible
with this hardware.

Download the correct FW file for the
controller.

Field Format Fail

Failed to reformat the field file system.

Replace controller.

Field Attach UBI Fail

Failed to attach (UBI) to the field file system. Replace controller.

Field Mount Fail

Failed to mount the field file system.

Replace controller.

Bad Update Method

Don’t know what our update method is.

Contact technical support.

No Firmware File Found Unable to find a firmware update file.

Thumb drive has no .scfx file. .scfx
file must be located at the root of
the USB drive.

Multiple Firmware Found Multiple firmware update files were found.

Too many .scfx files on the thumb
drive. Can only have on .scfx file
and must be located in the root of
the USB drive.

Firmware Invalid

Download the firmware file again
and retry download.

Firmware Invalid

Download the correct FW file again
and retry download.

Bad Firmware File

Unable to mount the firmware update file.

Download the firmware file again
and retry download.

Restore Failed

Database restore failed for some reason.

Try to restore using a different
backup file (Restore file may be
corrupt).

Hold

Crashed too many times and are now
“holding.”

Contact technical support.

Abnormal Termination

The embedded application terminated
abnormally.

Contact technical support.

Firmware Not Compatible

The firmware file downloaded is not
compatible with this hardware.

Download the correct FW file for the
controller.

Kernel Update Failure

Failed to update the kernel.

1. Try upgrading the controller

firmware again.

2. Replace controller.

Device Tree Failure

Failed to update the kernel device tree.

Not applicable for 210, 400, or 600.

Bootloader Failure

Failed to update the bootloader.

1. Try upgrading the controller

firmware again.

2. Replace controller.

Recovery Failure

Failed to update the recovery file system.

1. Try upgrading the controller

firmware again.

2. Replace controller.

Table 10. Marquee LED status and error codes

LED Blink Pattern

Message

Description

Action by User

Содержание Symbio 210













































































Результаты поиска

Содержание Symbio 210

Отзывы:

Похожие инструкции для Symbio 210

Бренды по названию

Популярные бренды

Trane Symbio 210, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Symbio 210

Отзывы:

Похожие инструкции для Symbio 210

Бренды по названию

Популярные бренды