Trane IntelliPak SCRF 25, Инструкция по установке, эксплуатации и обслуживанию

Страница: 40 / 120

40 SCXF-SVX01Q-EN
bushing in the plastic bag. Run the wires through
the bushing and connect wires to the unit.
5. After connecting wires and the static pressure tube,
raise the coil box up against the unit and install the
mounting screws. Recommended lifting points are
at each end of the coil box.
6. Avoid routing wires over devices and sharp edges.
Use wire ties about every 12 inches to secure wires
to other wire harnesses.
7. Move the entering air temperature sensor upstream
of the coil to ensure proper operation.
Refrigerant System
Trane Water Cooled Commercial Self-Contained units
ship factory charged with R-410A refrigerant.
Trane Air Cooled Commercial Self-Contained and
Condenser units ship with a dry nitrogen holding
charge.
Before installing refrigerant piping, verify holding
charge is present. Momentarily depress the CSC
suction or discharge line (and condenser liquid line)
access port valves.
If charge is present, continue with piping installation.
If no nitrogen escapes the access valve, leak test the
unit refrigerant system to determine the leak source,
and repair. See Maintenance section,
“Refrigerant Leak
Test Procedure,” p. 92 . After finding leak, remove test
pressure and repair leak using proper brazing
procedures. See Maintenance section,
“Brazing
Procedures,” p. 93 . Retest unit(s) to ensure all leaks are
repaired. Continue with piping installation.
Interconnecting Piping
Refrigerant piping must be properly sized and applied.
These two factors have a significant effect on both
system performance and reliability.
Using , select proper liquid and discharge line size. Unit
connection sizes are also shown. Install
interconnecting piping using proper installation and
brazing procedures.
Work on only one circuit at a time to minimize system
exposure to potentially harmful moisture in the air.
Before installing piping verify compressor oil levels are
near top of sight glass or above.
N No otte e:: CSC units (and replacement compressors) ship
fully charged with POE oil from the factory.
Scroll compressors use POE oil (OIL00079, quart
container or OIL00080, gallon container), DO
NOT substitute.
Capped discharge and liquid line connections are
located near bottom, left side of the indoor unit. CCRC/
CIRC connections are located in the unit front, at top.
Remove caps with a tube cutter to minimize risk of
getting chips inside piping.
N No otte e:: When facing the control panel side of the unit.
Circuit #2 is always on the left and Circuit #1 is
always on the right.
Cleanliness is extremely important during system
installation to minimize residual contaminants, such as
oxidization and scale.
Attach vacuum pump and begin evacuation as soon as
piping installation is complete. This starts system
dehydration and helps prevent POE compressor oil
contamination. This will also indicate large leaks if
vacuum does not hold (below 400 microns and hold for
2 hours). Complete LeakTest and Evacuation (for
procedures, see
“Refrigerant Leak Test Procedure,” p.
92 and “System Evacuation Procedures,” p. 93 in
Maintenance section) before starting “Preliminary
Refrigerant Charging,” p. 41 .
N No otte ess::
• Installation of a field supplied discharge line
access port near indoor units with optional
discharge line ball valve will make high side
pressure measurements easier during leak
test.
• UseType “L” refrigerant grade copper
tubing only.
N NO OT TIIC CE E
C Co om mp prre esssso orr D Da am ma ag ge e!!
P PO OE E o oiill iiss h hy yg grro osscco op piicc –– iitt a ab bsso orrb bss w wa atte err d diirre eccttlly y
ffrro om m tth he e a aiirr.. T Th hiiss w wa atte err iiss n ne ea arrlly y iim mp po ossssiib blle e tto o
rre em mo ov ve e ffrro om m tth he e cco om mp prre esssso orr o oiill a an nd d cca an n rre essu ulltt iin n
cco om mp prre esssso orr ffa aiillu urre ess..
T To o p prre ev ve en ntt P PO OE E o oiill ffrro om m a ab bsso orrb biin ng g w wa atte err,, tth he e
ssy ysstte em m ssh ho ou ulld d n no ott rre em ma aiin n o op pe en n ffo orr llo on ng ge err tth ha an n
n ne ecce essssa arry y.. W Wh he en n o op pe en n,, d drry y n niittrro og ge en n ssh ho ou ulld d ffllo ow w
tth hrro ou ug gh h tth he e p piip piin ng g.. O On nlly y n ne ew w o oiill cco on ntta aiin ne errss ssh ho ou ulld d
b be e u usse ed d ffo orr sse errv viicce e a an nd d m ma aiin ntte en na an ncce e.. A Allw wa ay yss u usse e
tth he e ssm ma alllle esstt cco on ntta aiin ne err ssiizze e rre eq qu uiirre ed d ffo orr tth he e jjo ob b
rre eq qu uiirre em me en nttss.. A Allw wa ay yss lle ea av ve e tth he e o oiill cco on ntta aiin ne err
ttiig gh httlly y sse ea alle ed d u un nttiill ttiim me e o off u usse e.. D Do o n no ott rre eu usse e o oiill
tth ha att h ha ass b be ee en n o op pe en ne ed d..
IIn nsstta alllla attiio on n -- M Me ecch ha an niicca all